The Cuz-D straight flush saw is a circular saw built to cut flush against walls and floors, cut underneath things and cut into 90-degree corners, which a standard circular saw cannot do. [1] Its blade sits on a recessed mounting point, so there is virtually zero clearance between the blade and the surface beside it. [2] Retailers list it as model SFS85. [3]
This matters if you tear out subfloors, trim door jambs or cut tight to a wall without chewing up the surface next to your cut. A regular saw leaves a strip you have to finish by hand, and the flush design is meant to remove that step.
Below you’ll find its key specs, how the flush cut works, the jobs it handles well and where it falls short. You’ll also see who should buy one and how to use it safely.
Key specs at a glance
The Cuz-D straight flush saw pairs a mid-size blade with enough depth to cut through standard framing lumber in one pass. Here are the numbers you need when sizing it up for your work.
Spec | Figure |
|---|---|
Blade diameter | 8 1/2 inches |
Cutting depth at 90 degrees | 3 inches |
Maximum cut depth (maker’s listing) | 3-1/8 inches |
Bevel capacity | 65 degrees and -5 degrees |
Weight | 14.3 lbs |
In the set | Stand, wrench and blade |
Blade size and cutting depth
The saw uses an 8 1/2-inch blade and cuts 3 inches deep at a 90-degree angle. [4] That depth covers a nominal 2×4 laid flat, which is 1 1/2 inches thick, with plenty of room left over. It also covers a stack of subfloor sheets or a door jamb with its trim still attached.
The maker lists a maximum cut depth of 3-1/8 inches. [1] The extra 1/8 inch gives you a little margin when the material runs slightly thick or the blade sits a bit off square.
Bevel range
The bevel tilts to 65 degrees for steep angled cuts, and it also goes to -5 degrees to keep the blade away from the wall. [3] A 65-degree setting lets you handle sharp miters on beams or rafters that a standard circular saw can’t reach.
Weight and what comes in the box
The saw weighs 14.3 lbs, and the set includes a stand, wrench and blade. [4] The wrench is for changing the blade, and the stand gives you a stable place to set the saw down between cuts so the blade doesn’t rest on the floor. Since a blade comes in the box, you can start cutting right away and buy spares once you know which tooth count suits your jobs.
How does it cut flush against a wall?
The Cuz-D cuts flush because of where the blade sits and which way it can tilt. A recessed blade mount lets the blade run right up against a wall, and a negative bevel angles the cutting edge slightly away from that wall so it doesn’t chew into it.
The recessed blade mount
On a standard circular saw, the blade sits inboard of the motor housing and guard. That housing hangs out past the blade, so when you push the saw against a wall, the blade stops short and leaves a strip of uncut material. On a typical subfloor cut, that strip is what forces you to finish with a chisel, a handsaw or an oscillating tool.
The Cuz-D mounts its blade at a recessed point, which gives it virtually zero clearance. [2] In practice, the blade face can ride along the wall, and the cut lands where the floor meets it instead of a short distance out.
The -5-degree bevel
Cutting flush has a catch: a blade running perfectly parallel to a wall tends to rub or score the surface beside it. The Cuz-D handles this with a -5 degree bevel setting that keeps the blade away from the wall. [3] A bevel is the tilt of the blade relative to the saw’s base, and a negative bevel tips it in the opposite direction from a normal angled cut.
That small tilt matters most at the bottom of the cut. The top of the blade stays tight to the wall while the cutting edge angles slightly back, so the kerf (the slot the blade removes) runs just off the finished surface.
What that means for your cut
Put together, the two features let you cut tight to the wall without gouging it. Pulling up a sheet of subfloor along a finished wall is a common example: with the negative bevel set, you can cut it out cleanly without damaging the sheetrock, wiring or plumbing next to it. [5]
Which jobs it handles best
The Cuz-D earns its keep on demolition and remodel cuts where the blade has to run tight against something you don’t want to damage. If your work regularly includes the four jobs below, it can save you prying, patching and second passes with a handsaw.
Pulling out subfloors
Subfloor removal is the headline job. The saw is built to cleanly extract subfloors without damaging the drywall, wires and plumbing next to them [5]. Picture a bathroom where the plywood is rotten right up to the wall: you can cut along the bottom plate and lift the panel out without chewing into the sheetrock above it or a supply line running underneath.
This is where flush cutting pays off most. A standard circular saw leaves a strip of floor along the wall that you would otherwise chisel or pry out by hand.
Water damage restoration
The maker lists water damage restoration as a core use [6]. After a leak, you often need to remove swollen flooring, wet sheathing or damaged framing quickly while keeping the surrounding structure intact. A saw that cuts right up to walls and into corners lets you take out only the ruined section, which keeps the repair area smaller.
Windows, beams, doorways and jambs
Remodel framing work is the other big category. Cutting out windows, trimming beams and cutting in doorways are among the jobs it was designed for [2]. The model is also sold as a jamb saw, so undercutting door jambs to slide new flooring underneath fits it well [4].
For example, when you widen a rough opening, you can trim a header or stud flush to the adjoining framing instead of leaving a stub to clean up later.
Two 2x4s in one pass
The 8.5-inch blade can cut through two 2x4s at once, and the seller describes it as the only saw on the market that can [7]. In practice, that means you can cut a doubled top plate or a pair of stacked studs in a single pass instead of flipping the work or finishing with a reciprocating saw.
Where it falls short
The Cuz-D is a specialty saw, and for most DIYers it won’t replace a general-purpose circular saw. It is built around one job: getting the blade tight against a wall, floor or corner. For everyday rip cuts on plywood or crosscuts on deck boards, a standard circular saw is lighter, cheaper to feed blades and easier to find parts for.
Weight and handling
The saw weighs 14.3 lbs with its set [4]. That is manageable when the saw rides on a subfloor, where the floor carries the weight. It gets tiring fast when you hold it overhead to trim a header or brace it one-handed while steadying a jamb with the other hand.
If much of your cutting happens above shoulder height or on a ladder, plan for two-handed grips and short sessions. A smaller flush-cut handsaw or oscillating tool may be easier for those spots.
Thin review history
At Acme Tools, the saw carries a 3.5 rating from only 6 reviews [3]. Six opinions is too few to tell you much about long-term durability or how common defects are. One unhappy buyer can pull that average down a full step, and one happy one can push it up.
Treat the rating as a weak signal. Talk to remodelers or restoration crews who use the saw, or ask a local dealer what returns they see.
Depth figures that don’t match
Listings give slightly different cut depths. One lists 3 inches at 90 degrees [4]. The maker’s store lists a max cut depth of 3-1/8 inches [1].
The 1/8-inch gap is small, but it matters if you plan to cut through two stacked 2x4s, which together measure about 3 inches thick. Plan around the lower 3-inch figure so a cut you expect to go all the way through doesn’t stop just short.
Should you buy one?
Buy the Cuz-D if flush cuts against walls, floors and jambs are a regular part of your work, and skip it if you only need a few clean trims a year. It’s a specialty saw, so its value depends on how often you’d reach for it.
Who it suits
The best fit is a remodeler or restoration crew that pulls out subfloors, trims jambs and opens up rooms week after week. The maker lists water damage restoration among the saw’s uses, the kind of job where you cut out soaked flooring right up to the wall [6]. If your crew does that every month, a saw built for zero-clearance cuts saves you from finishing every cut by hand.
Crews have a second option. Cuz-D sells a contractor 2-pack, which puts a saw in more than one pair of hands on a job site [5].
Who can skip it
If your projects are occasional DIY trim jobs, a flush-cut handsaw or an oscillating tool will likely cover them. Undercutting one door casing for new flooring, or trimming a single dowel flush, doesn’t call for a dedicated worm-drive saw. Those smaller tools cost less, store easily and handle light, one-off cuts.
A good test is to count the flush cuts you made last year. If you can list them on one hand, put the money toward a tool you’ll use more often.
Where to buy it
You can find the saw through the Cuz-D store on Amazon [1]. Acme Tools lists it as the Straight Flush Cut Saw SFS85 [3]. The maker also keeps a where-to-buy dealer list on its website [6]. Prices vary between sellers and change over time, so compare current listings before you order.
Using it safely near walls and floors
Before you plunge the blade into a floor or wall, find out what is behind or under it. A flush cut runs right along the edge of drywall and framing, which is exactly where electrical runs and supply lines tend to sit. The saw is built to pull out subfloors without damaging sheet-rock, wires and plumbing, but that only holds if you know where those wires and pipes are before you start [5].
Find hidden wires and pipes first
Shut off power to any circuit that runs through the area you are cutting. If you are taking out a subfloor, go to the basement or crawlspace and look up at the joists, or pull a register or outlet cover to see which way lines run. In a wall, check above and below outlets and switches, since cable usually runs straight up or down from them.
Mark anything you find with tape or a pencil line on the surface you will cut. A bathroom subfloor, for example, often has a supply line and a drain within a foot of the toilet flange.
Set the depth to the material
Set the blade depth to the thickness of the material you are removing, and no deeper. If you are cutting out 3/4-inch plywood subfloor, set the blade to just pass through the plywood so it stops short of anything below. A blade set deeper than it needs to be is the most common way to nick a pipe or cable you did not know was there.
Make a short test plunge in a scrap corner of the cut area, then look at the kerf to confirm you cut through without going into the joist.
Protect yourself and finish the cut cleanly
Wear safety glasses and hearing protection for every cut. Flush work throws chips and dust toward your face because you are low and close to the surface.
At the end of a cut, release the trigger and hold the saw in place until the blade stops completely. Lifting a spinning blade out of the kerf can make it catch the edge and kick.
The bottom line on the Cuz-D
The Cuz-D is a strong niche saw: it earns its place when you need to cut tight to a wall, floor or inside corner, and a regular circular saw can’t get close enough. Its recessed blade mount gives it virtually zero clearance [2], so it makes flush cuts, undercuts and cuts into 90-degree corners [1]. That is the job it’s built for.
If you cut out door jambs, window openings or subfloor sections every month, it pays for itself in saved patching time. If flush cuts come up once a year, a handsaw will do. For your next step, compare the current price against how many flush cuts you expect to make this year.
