DeWalt FlexVolt Advantage Circular Saw: Worth It Over the Atomic?

The FlexVolt Advantage saw (DCS573B) is a full-size 7-1/4 in. saw that runs on 20V MAX batteries and gets more power from FlexVolt packs. Here is when that extra capacity matters and when the compact Atomic is enough.

DeWalt FlexVolt Advantage Circular Saw: Worth It Over the Atomic?
In this article

Get the DeWalt FlexVolt Advantage circular saw (DCS573B) if you regularly cut thick framing lumber or rip long boards. It is a 7-1/4 in. brushless 20V MAX saw, so it runs on the batteries you may already own, though it saves its best performance for FlexVolt packs [1]. Paired with FlexVolt batteries, DeWalt rates it at up to 77% more power [2]. That extra power keeps the blade moving through dense or wet stock without bogging down.

The Atomic is the lighter, more compact choice. It suits trim, sheet goods and quick cuts around the house, and the companion review of the Atomic covers it in depth.

Below you’ll find how the two saws compare, how deep the FlexVolt Advantage cuts, which battery to pair with it, and when the Atomic is all you need.

How do the two saws compare?

The DCS573B is the full-size saw of the pair: it takes a 7-1/4 in. blade and spins it at 5,500 RPM, while the Atomic is DeWalt’s compact class built for lighter work [1]. The table below sticks to the specs the DCS573B lists. For the Atomic it gives only its size class and typical use, since its exact figures belong in the Atomic review.

Criterion

FlexVolt Advantage (DCS573B)

Atomic 20V Max

Size class

Full-size, sidewinder style [2]

Compact

Blade size

7-1/4 in. [1]

Smaller compact class

Max depth at 90°

2-9/16 in. [1]

Shallower; suited to thinner stock

Battery platform

20V MAX, with extra power on FlexVolt packs [2]

20V MAX

Best use

Framing lumber, thick stock, long rips

Light DIY cuts, one-handed work

What the numbers mean in the shop

A 7-1/4 in. blade is the standard size for framing saws. That means you can buy replacement blades almost anywhere, from fine-tooth plywood blades to coarse framing blades [3].

The 2-9/16 in. depth at 90° is the figure that matters most if you cut dimensional lumber [3]. A 2×4 or 2×6 is 1-1/2 in. thick, so you have about an inch of room to spare. That spare inch lets you cut through a board laid on sacrificial foam or a pair of sawhorses without bottoming out.

A faster blade gives you a cleaner, quicker cut in dense material such as oak shelving or pressure-treated posts. It also means you push the saw less hard through the cut.

Where the Atomic fits

The Atomic gives up depth and size so it stays light and easy to handle. If most of your cuts are 1/2 in. plywood, trim, or shelving boards, its smaller frame is easier to control on a ladder or in a cramped closet.

The gap between the two shows up on bigger jobs. If you rip a stack of 2x lumber for a deck or a shed, the DCS573B’s full-size blade and deeper cut are the reason to choose it. The Atomic is the better fit for cutting a few panels on a weekend project.

Two cordless circular saws of different sizes sit side by side on a wooden workbench covered in sawdust.

What does FlexVolt Advantage actually do?

FlexVolt Advantage lets the saw run on the 20V MAX batteries you already own and draw extra power when you snap on a FlexVolt pack. You don’t need a new battery platform to use it. The saw is sold as a 20V MAX tool, so any pack from that lineup fits and runs it. [2]

It works with the batteries you already have

If you own a DeWalt drill or impact driver, its 20V MAX battery will power this saw. That keeps the cost of entry down, because you can start cutting with what’s on your shelf and decide about bigger packs later. [4]

The name can be confusing. “FlexVolt” on a battery means a higher-capacity pack that also fits 20V MAX tools. “FlexVolt Advantage” on a tool means the tool is built to sense that pack and take advantage of it.

More power on a FlexVolt pack

On a FlexVolt battery, the saw delivers up to 77% more power than it does on a standard pack. [2] In practice, that extra headroom shows up when the blade is buried in a long, thick cut, like ripping a 2×10 or crosscutting wet pressure-treated lumber. On those cuts the motor is less likely to bog down. [4]

The words “up to” matter. You’ll see the biggest gain on hard, heavy cuts. On a quick crosscut through a 1×4 shelf board, both battery types finish the job before the difference shows.

Competent on 20V, top-tier on FlexVolt

Hands-on testing describes the saw as competent with standard 20V MAX batteries and top-tier with FlexVolt batteries. [5] So the saw is a solid tool on a regular pack, and it moves up a class when you give it the bigger one.

That gives you two practical ways to use it:

  • Run it on a 20V MAX pack for trim, sheet goods and occasional framing cuts around the house.

  • Pair it with a FlexVolt pack for deck builds, stair stringers or a day of ripping dimensional lumber.

This flexibility is the main thing the Advantage name buys you. You get one saw that handles light work on the batteries you have and harder work when you add a bigger battery.

A carpenter pushes a cordless circular saw through a thick wooden beam, sending sawdust into the air.

How much can it cut?

The DCS573B cuts through standard 2x framing lumber in a single pass, with room to spare. Its maximum depth of cut is 2-9/16 in. at 90° [1]. A 2×4 or 2×6 is actually 1-1/2 in. thick, so the blade clears it with about an inch left over, and you never have to flip the board and cut from the other side.

Depth at 90°

Depth of cut is how far the blade reaches below the saw’s base plate. At a square 90° setting, this saw reaches 2-9/16 in. [1] That covers most of what a homeowner or DIYer cuts on a deck, shed or framing job.

Here is how common stock compares with that depth:

Material

Actual thickness

One pass at 90°?

1/2 in. plywood

1/2 in.

Yes

3/4 in. plywood or MDF

3/4 in.

Yes

2×4 or 2×6 lumber

1-1/2 in.

Yes

Two stacked sheets of 3/4 in. plywood

1-1/2 in.

Yes

The table covers square cuts. Tilting the shoe for a bevel shortens the blade’s reach, so plan on less depth for angled cuts.

Material range

The saw handles everything from sheet goods to thick hardwood. In hands-on testing it cut materials from 1/2 in. plywood to 2 in. thick hardwood without losing power [6]. That means you can break down a sheet of plywood for shelving and then rip 2 in. oak for a workbench top without changing saws.

Hardwood is where a saw usually bogs down, because dense wood such as maple or oak resists the blade more than pine does. A saw that keeps its speed in 2 in. hardwood gives you cleaner edges and less burning. Pair it with a sharp blade that has the right tooth count for the job.

Motor speed

A brushless motor spins the blade at 5,500 RPM for fast cutting [1]. Higher blade speed means each tooth takes a smaller bite, so the cut moves faster and leaves a smoother edge. Brushless motors also have no carbon brushes to wear out. More of the battery’s energy goes into the cut instead of being lost as heat, which helps on long rip cuts.

Which battery should you run it on?

Plan on buying at least one battery, because the bare tool version of this saw ships without a pack or charger. If you already own DeWalt 20V MAX batteries, you can start cutting with those. If you don’t, the battery is a real part of your budget and your cutting experience.

Start with what you already own

A “tool only” or “bare tool” listing means you get the saw body and nothing to power it. That suits you if you have a shelf of 20V MAX packs from a drill or impact driver. It is a poor fit if this is your first DeWalt cordless tool, since you would need to buy a battery and charger before your first cut.

Small packs work, but they drain quickly in a 7-1/4 in. saw. A compact 2Ah battery from a drill kit will handle a few crosscuts on 2x4s. It runs out fast if you try to break down a full sheet of plywood.

A 6Ah pack is a sensible everyday choice

A larger 6Ah pack gives you enough capacity for a real work session, and one review called out the battery life on a 6Ah pack specifically [6]. That same review found the saw cut from 1/2 in. plywood up to 2 in. hardwood without bogging down [6]. For a homeowner building shelves, cutting deck boards or trimming sheet goods, a 6Ah battery keeps you working without constant swaps.

Get a FlexVolt pack if you rip a lot

A FlexVolt battery is worth the extra cost when your cuts are long and thick. Reviewers describe the saw as competent on standard 20V MAX batteries and top-tier on FlexVolt batteries [5]. You feel that difference most on ripping, where the blade runs along the grain for the full length of a board and the motor works hardest.

Here are two quick ways to decide:

  • Stick with a 20V MAX pack if you mostly crosscut 2x lumber and plywood for weekend projects.

  • Add a FlexVolt pack if you regularly rip long 2x10s, cut stair stringers, or work through dense hardwood.

FlexVolt packs are heavier, so the saw feels bulkier in your hands. If you rarely make heavy cuts, that extra weight buys you little.

Do you need it, or is the Atomic enough?

Buy the FlexVolt Advantage saw if you regularly cut thick stock, and stick with the Atomic if your projects are mostly light trim, sheet goods and quick one-handed cuts. The deciding factor is how often your work pushes a saw hard. The occasional board doesn’t settle it.

Pick the FlexVolt Advantage for frequent thick cuts

This saw suits work where the blade stays buried in the wood for long stretches. Think framing a shed, building a deck, or ripping long hardwood boards for a workbench top. The full-size 7-1/4 in. format gives you the depth and power those jobs need.

It also makes sense if you already own DeWalt 20V MAX packs and plan to add a FlexVolt battery later. One reviewer called it competent with standard 20V Max batteries and top-tier with FlexVolt batteries. [5] In practice, you can start on the batteries you have and move up only if your cuts feel sluggish.

The trade-off is size. A full-size sidewinder is heavier and bulkier to carry up a ladder or hold overhead, so it is less pleasant for quick trim cuts.

Pick the Atomic for light, one-handed DIY work

The Atomic is the better match when your cuts are short and frequent. Typical jobs include trimming shelving, cutting plywood panels for a cabinet back, or notching a fence picket. Its compact build is easier to control with one hand and easier to store in a small shop or garage.

If most of your projects use thin stock, the extra capacity of the FlexVolt Advantage mostly goes unused. You would carry more weight for power you rarely need. The pillar review of the Atomic covers what it handles well and where it runs short.

What owners think

Buyers rate the FlexVolt Advantage saw well. It averages 4.5 stars across 513 ratings at one retailer [2] and 4.4 stars across 357 ratings at another. [3] Those scores come from hundreds of owners, so a single bad experience doesn’t drive them. They show steady satisfaction among people who bought it for the work it is built for.

Making the call

Your usual stock thickness decides this purchase. If you regularly cut 2x framing lumber, stacked sheets or thick hardwood, the FlexVolt Advantage’s 2-9/16 in. maximum depth at 90° means you finish those cuts in one pass instead of flipping the board [1]. If most of your work is 1/2 in. plywood, trim and shelving, that extra depth sits unused.

Measure the boards you cut most often, say the 2x6s for a deck repair or the 3/4 in. plywood for a workbench, and match the saw to that. Then look up the current price of the DCS573B tool-only kit and the battery you plan to pair with it on the retailer’s page before you buy, since the bare tool and packs are sold separately.

Sources

  1. 20V MAX* 7-1/4-in Brushless Cordless Circular Saw With …

  2. 20V MAX Cordless Brushless 7-1/4 in. Sidewinder Style …

  3. DEWALT 20V MAX Brushless Cordless Circular Saw w

  4. DeWalt DCS573B 20V MAX 7-1/4-Inch Brushless Cordless …

  5. DeWalt FlexVolt Advantage Circular Saw

  6. DeWalt 20v MAX Circular Saw w/ FLEXVOLT ADVANTAGE