The WEN Plunge Cut Circular Saw Bundle is the first pick for most DIYers who need to break down full sheets of plywood. Its two 50-inch rails join to make straight cuts over 8 feet long, so you can rip a 4×8 sheet in one pass without moving the track. For a closer look, read Who Makes the Best Track Saw? Festool, Mafell and Makita Compared.
A track saw is a plunge-cut circular saw that rides on a guide rail, which gives you straight, splinter-free cuts without a table saw. That matters when you’re cutting cabinet sides in a garage shop or trimming a door where tearout would show.
The five picks below cover a budget bundle, two corded saws for heavier work and a cordless model for jobs away from an outlet, with what each does well and where it falls short.
As an Amazon Associate we earn from qualifying purchases.
How we picked: from products sold on Amazon for this need, compared by what their makers state and what buyers report in their reviews.
The Picks at a Glance
Product | Best for | Item dimensions l x w x h | Item weight | Blade length | Buyer rating | |
|---|---|---|---|---|---|---|
WEN Plunge Cut Saw Bundle | cutting full sheets on a budget | — | — | 16.5 centimeters | 4.6 of 5 (332 reviews) | |
DEWALT DWS520K | kickback-conscious hardwood cutting | 18.06″L x 12.38″W x 12.13″H | 0.69 kg | 8 in | 4.2 of 5 (184 reviews) | |
Makita SP6000J1 | cutting varied materials | 59″L x 12″W x 14″H | 10.6 lb | 2 in | 4.6 of 5 (1,289 reviews) | |
WEN CT1065 | adding a saw to a track you already own | 12″L x 9.5″W x 9.5″H | 0.27 g | 6.5 in | 4.4 of 5 (1,598 reviews) | |
WEN 20691 Cordless | cutting away from an outlet | 12.99″L x 9.84″W x 9.84″H | 6.92 kg | 6.5 in | 4.4 of 5 (101 reviews) |
Buyer ratings as shown on Amazon on November 19, 2026; they change.
WEN Plunge Cut Saw Bundle: Best for cutting full sheets on a budget

The WEN bundle suits DIYers who need to break down full sheets of plywood without spending on a pro kit. It pairs a 10-amp 6.5-inch plunge cut saw with two 50-inch guide rails that let you make straight cuts over 8 feet long.
The maker rates the saw for cutting depth up to 2-1/3 inches, with 45-degree bevel cuts in boards up to 1-5/8 inches thick. That depth clears 3/4-inch plywood and 2x lumber with room to spare. The bevel limit covers mitered edges on cabinet sides and shelving, though not on very thick stock.
The two rails join with adapters, and the rubber lip on them helps with dust control. Joined end to end, they span a full sheet lengthwise, so you can rip a 4×8 panel in one pass instead of moving a short guide partway through. Grooves in the saw base let it slide along the track, and the adapter set uses 4 set screws for stability. Snug set screws keep the joint between rails from shifting, which is where a long cut usually drifts. The saw is corded, so you work within reach of an outlet or extension cord.
Pros
Two rails handle cuts over 8 feet
Deep enough for common sheet goods and 2x stock
Adapters with set screws keep joined rails steady
Rubber lip on the rails helps with dust control
Cons
Clamps are sold separately, so holding the track down on slick sheets is an extra purchase.
Corded power ties you to an outlet on job sites and in yards.
If you mostly cut away from power, look at the WEN 20691 Cordless instead.
DEWALT DWS520K: Best for kickback-conscious hardwood cutting

The DEWALT DWS520K is the pick if you cut a lot of hardwood and want extra protection against kickback. It pairs a 12A, 1300W motor that handles hardwoods up to 2-1/8 inches thick with a continuous anti-kickback mechanism and a riving knife. That makes it a good match for furniture makers and anyone ripping thick oak or maple boards.
DEWALT rates the on-track cut depth at 2-1/8 inches at 90 degrees and 1-5/8 inches at 45 degrees, and the depth scale accounts for the track’s thickness. In practice, a 2x lumber rip or a 45-degree miter on 1-1/2-inch stock fits within its range, and you can set the depth by reading the scale instead of doing math around the rail. The anti-kickback mechanism and riving knife work to prevent kickback when engaged. A riving knife is a thin metal fin behind the blade that keeps the cut from pinching closed, which is where kickback in dense hardwood usually starts.
The saw runs on dual-edged tracks that give straight cuts in both directions. You can flip the rail end for end and still cut along its edge, which helps when your workpiece only lets you reach it from one side. The kit includes a 48-tooth fine finishing blade, and the saw is corded at 120 volts, so it needs a nearby outlet or extension cord.
Pros
Strong 12A motor for thick hardwood
Anti-kickback mechanism plus riving knife
Buyers say cuts are straight and very accurate
Buyers report dust collection keeps the work area clean
Cons
Some buyers find it fidgety and not easy to use
Some buyers say it does not run smoothly
Corded, so you are tied to an outlet
If you work away from power, the WEN 20691 Cordless is the better fit.
Makita SP6000J1: Best for cutting varied materials

The Makita SP6000J1 suits you if you cut more than plywood and want to tune the saw to each job. Its 12-amp motor has a variable speed dial from 2,000 to 5,200 RPM, which the maker pitches for performance in a variety of materials. In practice you can run full speed through sheet goods and slow the blade for material that burns or chips at high speed.
The maker adds electronic speed control that holds a constant speed under load. That means the blade keeps its pace as you push into a thick or dense board, so you get smoother cuts with less bogging down. The kit comes with a 6-1/2-inch 48-tooth carbide-tipped blade. A blade with that many teeth leaves a finer edge than a rough framing blade.
Cut depth is 2-3/16 inches at 90 degrees and 1-9/16 inches at 45 degrees. That handles 3/4-inch plywood and standard 2x lumber with room to spare. The bevel tilts from -1 to 48 degrees with positive stops at 22.5 and 45 degrees. Those stops let you set common miter angles quickly without fiddling, and the extra degrees past 45 help when a joint needs a slight back-cut. The saw plugs into a standard 110-volt outlet.
Pros
Variable speed for matching the blade to the material
Bevel stops at 22.5 and 45 degrees for quick angle setup
Buyers say it cuts cleanly through plywood with very little tearout
Buyers find setup intuitive and blade changes easy
Cons
The kit comes with one 55-inch guide rail, so you need extra rail or two passes to cut a full 8-foot sheet lengthwise.
Buyers report the guide rail can shift slightly side to side during a cut, so clamping it down matters.
It is corded, so you are tied to an outlet.
If you mostly break down full sheets, the WEN Plunge Cut Saw Bundle with its longer rail setup fits better.
WEN CT1065: Best for adding a saw to a track you already own

The WEN CT1065 is the saw to buy if you already have a WEN track and want to add the saw on its own. It works with the WEN CT9502 100-Inch Track and the WEN CT992F Track Saw Clamps, so you can pair it with rails and clamps you may already have in the shop. It is a corded, 10-amp, 120-volt saw, so it plugs into a standard household outlet.
The saw rips boards up to 2-1/3 inches thick and makes 45-degree bevel cuts in boards up to 1-5/8 inches thick. That covers 3/4-inch plywood and standard 2x lumber with room to spare, and lets you bevel the edge of a shelf or a box side. It also does internal plunge cuts, so you can start a cut in the middle of a panel, for example to cut an opening for a sink or a vent.
It comes with a 6.5-inch, 24-tooth carbide-tipped blade on a 20 mm arbor and runs at 4500 rpm. When you shop for a replacement blade, look for that 6.5-inch size and 20 mm arbor so it fits the saw.
Pros
It pairs with the CT9502 100-inch track and CT992F clamps
It does plunge cuts in the middle of a panel
Buyers say it cuts straight lines on both short and long cuts
Buyers call it good value as an entry-level track saw, and say it cuts better with a quality replacement blade
Cons
The track is sold separately, so if you own no rail you need to buy one before you can make guided cuts
Buyers complain that the plunge lock is troublesome and makes the saw harder to use
Buyers report that it wobbles on the track and that some plastic parts feel flimsy
If you are starting with no track at all, the WEN Plunge Cut Saw Bundle gives you the saw and rails in one box.
WEN 20691 Cordless: Best for cutting away from an outlet

The WEN 20691 is the pick if you cut where there’s no outlet nearby, like a driveway, a job site or the far end of a yard. It runs on two 20V Max batteries instead of a cord, and the kit includes the batteries and a charger, so you can start cutting out of the box.
The maker lists a brushless motor fed by dual 20V Max battery ports, with variable speed from 2000 to 5500 RPM. Variable speed lets you slow down for materials that chip or burn at full speed, and with no cord there’s nothing to drag across the sheet or snag on the end of the rail mid-cut.
The two 4.0 Ah lithium-ion batteries have onboard LED charge gauges and fit the entire WEN 20V Max Cordless Power Tool series. If you already own WEN 20V tools, your spare batteries work here, and these two will run your drill or other WEN tools too. Having two batteries means one can charge while the other cuts.
The saw rips boards up to 2.25 inches thick and makes 45-degree bevel cuts in boards up to 1.65 inches thick. That covers plywood, MDF and most dimensional lumber you’d cut at home. It works with the WEN CT9502 and CT9110 tracks and the WEN CT992F clamps, and the kit includes a 48-tooth carbide-tipped 6.5-inch blade, a dust port adapter and a two-year warranty. The track is not part of this kit, so you’ll pair it with one of those WEN rails.
Pros
Cordless, so you can cut anywhere
Batteries swap with other WEN 20V tools
Buyers say the batteries last most of a day of heavy cutting
Buyers report accurate cuts, even on long rips, and easy setup
Cons
Buyers question its durability, with the regular plunge mode breaking easily
At 6.92 kg, it’s heavier than the Makita SP6000J1 at 10.6 pounds, which you’ll feel when lifting it onto the rail all day
If you always work near an outlet and want rails in the box, the WEN Plunge Cut Saw Bundle is a better fit.
What to look for when choosing a track saw
Start with the rail: it decides how long a straight cut you can make in one pass. To break down a full 4×8 sheet of plywood lengthwise, you need rails that add up to about 8 feet. Two 50-inch rails joined together, for example, let you make straight cuts over 8 feet long. A single 55-inch rail handles crosscuts and shorter rips, but you’ll need a second rail for full-length sheet cuts.
Next, decide between corded and cordless. A corded saw runs as long as you have an outlet and an extension cord. A cordless saw lets you cut in the driveway or on a job site. If you go cordless, pick a battery platform you already own or plan to grow into: batteries that are compatible with the entire WEN 20V Max Cordless Power Tool series can be shared with your other tools from that line.
Then match cut depth to your thickest stock, at both 90 and 45 degrees. Depth always drops on a bevel. One saw cuts 2-1/8 inches at 90 degrees but only 1-5/8 inches at 45 degrees on the track. That is plenty for 3/4-inch plywood, and it still lets you bevel a 1-1/2-inch-thick board.
Finally, look at safety features and clamping. A riving knife and an anti-kickback mechanism help keep the saw from kicking back toward you when they are engaged. Clamps hold the rail in place so it doesn’t creep mid-cut. Budget for them if your kit leaves them out, since some bundles sell clamps separately.
Which track saw to start with
The WEN Plunge Cut Circular Saw Bundle is the first pick for most DIYers who need to break down full sheets of plywood at home. It comes with a saw and rails in one box, so you can make long, straight cuts on day one without buying a track separately.
Your next step is to decide between corded and cordless before you compare anything else. A corded saw like the bundle runs as long as you have an outlet nearby. If you cut in a driveway or at a job site, the WEN 20691 runs on two 20V Max batteries that also fit other WEN 20V tools. Once you know which power source fits where you work, the rest of your shortlist gets much shorter.