A chainsaw cuts with a loop of sharp teeth that a motor drives around a flat metal guide bar, and you keep both hands on the saw every second it runs. That second habit matters as much as the cutting itself, because a saw held with one hand can jump or twist before you can react. [1]
If you’re buying your first saw or pulling an old one out of the garage, these chainsaw basics give you a safe starting point. You’ll learn the main parts and safety features, how gas, corded and battery saws compare, and how to pick a bar size. The guide then covers how to start the saw, how to hold it and cut, and the routine care that keeps your chain sharp and your saw running. [2]
Key takeaways
The chain’s teeth travel around the guide bar to make the cut.
Hold the saw firmly with both hands whenever it runs.
Power type and bar size should fit the jobs you do most.
How does a chainsaw work, and what are its main parts?
A chainsaw uses a gas engine or an electric motor to spin a small toothed wheel, called the drive sprocket, which pulls a loop of cutting chain around a flat steel bar. The teeth on the chain do the cutting as they race along the edge of the bar, so the saw cuts wherever you press that moving edge into the wood.
The parts that do the cutting
The cutting system has four main pieces, each with its own job:
The guide bar is the long, flat metal blade the chain rides on. A groove runs around its edge to keep the chain on track.
The chain is a loop of linked steel with sharp cutting teeth on top and drive links underneath that sit in the bar’s groove.
The drive sprocket sits behind a side cover near the motor. Its teeth catch the chain’s drive links and pull the chain around.
The handles give you two grips: a rear handle with the throttle trigger and a front handle that wraps over the top of the saw.
A simple way to picture it is a bicycle chain on a gear, stretched around a long, narrow track instead of a second gear.
Safety features built into the saw
The chain brake is the most important safety feature on a modern chainsaw. It is linked to the front hand guard, the curved shield just in front of the front handle. When you push that guard forward, or when a sudden jolt throws it forward, the brake clamps down and stops the chain almost at once.
That sudden jolt is usually kickback, the fast upward and backward kick of the bar toward you. The chain brake is there to stop the chain before it reaches you if the saw kicks back.
Most saws add a few more protections:
A throttle lockout, a small lever on the rear handle that keeps the trigger from engaging unless your hand is wrapped around the grip.
A chain catcher, a small hook under the bar that grabs the chain if it breaks or jumps off.
A rear hand guard that shields your back hand from a thrown chain or flying debris.
Anti-vibration mounts between the handles and the motor that cut down on hand fatigue during longer jobs.

Gas, corded or battery: which chainsaw fits your yard?
Pick the power type by where you cut and how much: a gas saw suits big or remote jobs, while a battery or corded saw suits light trimming close to the house. Then pick a bar length that fits the wood you cut most often, since a bar far longer than you need is just extra weight to swing around.
Gas saws for heavy work away from outlets
A gas saw carries its own fuel, so you can work at the back of a wooded lot, along a fence line or at a storm-damaged tree far from any outlet. When the tank runs low, you refill it and keep going. That makes gas the usual choice for cutting firewood by the cord or clearing several downed trees in a day.
The trade-offs are noise, weight and upkeep. You mix or buy fuel, deal with exhaust and give the engine more care than an electric motor needs. If you only cut a few times a year, that upkeep can outweigh the extra power.
Battery and corded saws for light jobs near home
For pruning limbs, trimming shrubs or cutting a fallen branch into pieces you can haul, an electric saw is often enough. These saws are lighter and quieter, and they start without a pull cord.
The two electric types differ in one practical way. A corded saw runs as long as it is plugged in, but the cord limits how far you can go and can snag on brush. A battery saw goes anywhere in the yard, and its runtime ends when the pack does, so a spare battery helps on a longer job.
Matching bar length to your wood
The guide bar is the long, flat metal arm the chain runs around, and its length sets how thick a log you can cut comfortably. Buy for the wood you cut most often, not the biggest tree you might face someday.
If most of your work is branches and small limbs, a short bar is easier to control and less tiring to hold. If you regularly buck thick logs into firewood, you need a longer bar, and that usually means a more powerful saw to pull the chain through the cut. Measure a few of the logs you cut most and choose a bar that clears them with some room to spare.

How do you start a chainsaw safely?
Start a chainsaw with the chain brake on and the saw resting on the ground, held steady by your foot and your free hand. Never drop-start it. [1] That means you never hold the saw in the air with one hand while yanking the starter cord with the other. When you start it that way, nothing controls the bar while the engine catches, and the moving chain can swing toward your legs.
The chain brake locks the chain so it cannot spin. With the brake on, the engine can fire and idle while the chain stays still, which gives you a moment to get set before anything is cutting.
Steps for a safe start
Push the chain brake forward so it is engaged before you touch the starter. [1] On most saws the brake is the hand guard in front of the top handle, and it clicks into place.
Set the saw on flat, clear ground, away from logs, rocks and loose debris the chain could touch. Bare dirt or short grass works well. A pile of brush does not.
Brace the saw with your foot and your free hand. [1] On a rear-handle saw, slide the toe of your boot into the rear handle and press down, and grip the front handle firmly with your left hand. The saw should not rock or slide when you pull.
Pull the starter cord with your right hand. Start with a short pull until you feel resistance, then pull firmly. Let the cord rewind under control instead of letting it snap back.
Once the engine is running, pick the saw up and put both hands on the handles. Your right hand goes on the rear handle and your left hand on the front handle, with your thumb wrapped around it.
Release the chain brake by pulling the hand guard back toward the front handle, keeping both hands on the saw while you do it. [1] The chain is now free to move when you squeeze the throttle.
If the engine stalls or you need to set the saw down, push the brake forward again before you let go of either handle. Then repeat the same braced, on-the-ground start before you pick the saw up again.
What is the right way to hold and cut with a chainsaw?
Hold the saw firmly with both hands every time the chain is moving, and keep the tip of the bar away from anything you aren’t cutting. Always hold the chainsaw firmly with both hands [3]. Most cutting mistakes beginners make come back to a loose grip or a bar tip that drifts into something.
Get a firm two-handed grip
Your right hand goes on the rear handle with the throttle, and your left hand wraps around the front handle. Wrap your thumb under the front handle so your fingers and thumb circle it. A saw held with fingertips can jump or twist when the chain bites. A full grip lets your arms absorb that movement.
Stand with your feet apart and your body slightly to the left of the bar, not directly behind it. Let the saw do the work. Run it at full speed as the chain meets the wood, then ease the bar through without forcing it down.
Keep the bar tip clear
The tip of the bar should never touch other objects [3]. The danger zone is the upper quarter of the tip. If the moving chain catches there on a log, a branch, a fence post or the ground, the saw can be thrown back toward you.
A few habits keep the tip clear:
Look past the cut before you start and spot any nearby branches, rocks or a second log.
Cut with the lower edge of the bar, where the chain pulls the saw away from you.
Finish a cut through a log on the ground before the tip reaches the dirt, then roll the log to finish from the other side.
Avoid reaching into a pile and cutting with only the tip.
Slow down on twigs and thin branches
Take extra caution when cutting twigs and other thin material [3]. Small branches are light and springy, so the chain can grab one and fling it, or wrap it around the bar instead of slicing through.
For brush and limbs thinner than your wrist, cut one piece at a time instead of a tangled bundle. Support the branch so it can’t whip, and clear cut pieces away before the next cut so they don’t catch the bar tip.
What routine care keeps a chainsaw cutting well?
A chainsaw that cuts well comes down to three habits: keep the chain sharp and properly tensioned, top up the bar oil before every job, and clean the saw before you put it away with the bar covered. None of these takes long, and together they make the saw easier to control and kinder to its parts.
Keep the chain sharp and correctly tensioned
A sharp chain pulls itself into the wood and throws out coarse chips. A dull one makes fine sawdust, and you end up pushing the saw to make it cut. When you notice dust instead of chips, or the saw drifts to one side in a straight cut, sharpen the chain or swap in a fresh one.
Tension is the other half. A chain that sags under the bar can jump off while you cut. A chain pulled too tight binds and wears the bar and sprocket faster. Check tension with the saw switched off and the chain cool, and adjust it with the tensioning screw or knob your saw’s manual shows.
New chains stretch during their first few cuts. Check the tension again after a short session.
Check bar oil before each job
Bar oil keeps the chain sliding smoothly along the guide bar. Without enough oil the chain runs hot and the bar wears quickly. Make filling the bar oil reservoir part of your routine before every job, the same way you check fuel or battery charge.
You can see whether oil is reaching the chain: hold the running saw over a light-colored surface such as a stump or a scrap of cardboard. A thin line of oil spray means the oiler is working. A dry chain or an empty reservoir tells you to stop and refill.
Clean the saw and store it with the bar covered
Sawdust and pitch pack into the area around the sprocket cover, the bar groove and the air vents. After a job, brush that debris out so it doesn’t build up and clog the oiler or trap heat. Scraping the groove on the bar also helps fresh oil reach the chain the next time you use it.
Slide the scabbard (bar cover) over the bar and chain before you store the saw. The cover protects the teeth from getting nicked, and it protects you when you reach for the saw on a shelf. Keep the saw somewhere dry so the chain and bar don’t rust between jobs.
Your first cuts with a chainsaw
Keep both hands on the saw every time it runs, and you avoid most beginner mistakes. Always use both hands to operate the chainsaw, and never drop-start it [1]. Before each start, put the chain brake on and steady the saw with your foot and free hand [1].
For your next step, practice on small, firewood-size logs that sit firmly on the ground or on a sturdy sawbuck, so the wood can’t roll or pinch the bar. Keep the tip of the bar away from other logs and the ground [3]. Skip brush piles and thin branches until you’re comfortable, because twigs and other small material call for extra caution [3].