Irwin Speedbor Spade Bits: What They Do and Who Should Buy Them

Speedbor spade bits are fast, affordable bits for boring holes in wood. Here is what the Blue-Groove design does, which jobs suit them and when a set beats single sizes.

An IRWIN spade bit set in a blue plastic case, showing graduated flat drill bits and a hex extension, with yellow 2X labels.
In this article

Irwin Speedbor spade bits are flat, paddle-style wood-boring bits made to drill holes fast. They do best on rough holes where speed matters more than a polished edge, such as running wire or pipe through framing.

The speed comes from Irwin’s patented Blue-Groove point and cutting edge, which is built for faster chip removal and drilling speed [1]. Irwin also says the design gives reduced breakout and cleaner holes [1]. The cutting edge removes wood chips aggressively, so the bit keeps biting instead of clogging [2].

If you’re drilling a dozen studs for a new circuit, that speed saves real time. If you’re boring a visible hole in a cabinet face, you’ll want a different bit. Below you’ll find what the design does, the jobs these bits fit, how fast they drill, where they fall short, and whether to buy a set or single sizes.

What makes the Blue-Groove design different?

The Blue-Groove design is Irwin’s patented point and cutting edge, shaped to clear wood chips quickly so the bit keeps cutting instead of clogging. Irwin says the design gives faster chip removal and drilling speed, reduced breakout, and cleaner holes. [1]

How the groove changes the cut

A spade bit is a flat paddle with a center point and two cutting edges. As those edges shave wood, the chips have to go somewhere, and when they pack into the hole the bit slows down, heats up and starts to tear the fibers.

The Blue-Groove cutting edge allows aggressive removal of wood chips and fast drilling. [2] In practice, that means less stopping to back the bit out and clear the hole. This matters most when you are boring through a 2×4 stud or a run of joists one after another.

Less breakout on the far side

Breakout is the splintered crater that forms where the bit exits the board. It happens when the bit pushes through the last thin layer of wood instead of cutting it cleanly. Reduced breakout and cleaner holes are two of the results Irwin attributes to the Blue-Groove point and edge. [1]

For wiring and plumbing holes inside a wall, a little tear-out rarely matters. A cleaner exit still helps when the hole will show, such as a cord pass-through in a shelf back.

Edges and tip built to last

The cutting edges are chamfered, meaning their corners are beveled, for increased durability and longer life. [3] A beveled edge is less likely to chip than a sharp square corner when it hits a hard knot.

The point tip is also shaped to help minimize splintering and control speed. [3] The tip pulls the bit into the wood and keeps it centered, so the cutting edges meet the surface evenly. That gives you a rounder hole entry and fewer splinters around the rim.

Which jobs are Speedbor bits good for?

Speedbor bits are made for quick, rough holes in framing lumber, so they fit rough-in work where nobody will see the hole once the drywall goes up. Think of a 3/4-inch hole through a row of studs for a PEX line, or a 5/8-inch hole through a joist so you can pull a cable to a new outlet.

Wiring and plumbing holes through studs and joists

The sizes in a typical set line up with common rough-in jobs. The 8-piece set includes 3/8, 1/2, 5/8 and 3/4 inch bits along with larger sizes. [4] A smaller bit handles a single low-voltage or speaker wire, and the 3/4-inch bit leaves room for a water supply line or a couple of electrical cables pulled together.

On this kind of work, a clean entry matters less than getting through the wood. You drill, feed the line, and move to the next stud. A spade bit’s flat, wide shape cuts a full-size hole in one pass, so you don’t need to start small and step up.

Through-holes and countersinking

Speedbor bits are designed for drilling through-holes and for countersinking, with smooth holes and reduced breakout. [4] Breakout is the splintering that happens where the bit comes out the back side of the board. When there’s less of it, the back face stays usable and you spend less time cleaning up ragged fibers.

Countersinking here means boring a shallow, wider hole so a bolt head, nut or washer sits flush with or below the wood surface. For example, if you’re bolting a 2×6 ledger or building a workbench frame, you can drill a 1-inch recess partway in and then switch to a smaller bit for the bolt shank.

6-inch versions for deeper reach

Irwin also sells an 8-piece Speedbor set with 6-inch bits, with sizes starting at 3/8 inch. [5] The extra length lets you drill through doubled top plates or a stack of lumber in one pass. It also helps when you need to reach between closely spaced framing, where the drill body can’t get square to the board.

If most of your holes go through a single 2×4, standard-length bits are enough. Pick the 6-inch bits when you’re running lines through doubled or tripled framing, or when you need to reach into a tight spot.

Electrician drilling a large hole through a wooden wall stud with a spade bit to run electrical cable through the framing.

How fast do they actually drill?

Speedbor bits are quick. In a hands-on review test, a 1-inch Speedbor averaged 3.66 seconds per hole, which made it the fastest bit in that comparison. [6] A hole in a few seconds lets you keep moving down a wall instead of waiting on the drill.

What the test number tells you

The 3.66-second figure is an average over several holes, so it reflects steady performance rather than one lucky pass. [6] For you, that means a fresh 1-inch Speedbor should feel aggressive and push through without much coaxing.

Treat the number as a comparison point. Your own times will depend on your drill’s power, the wood, and how sharp the bit is. A cordless drill with a tired battery or a knotty board will slow any bit down. The ranking still tells you this design cut faster than the other bits it was tested against.

Where the speed pays off

Speed counts most when you drill the same hole over and over. Think of running a new electrical circuit along a basement wall, where you might bore through a stud every 16 inches for 20 feet or more. That adds up to more than a dozen holes in a row.

At a few seconds per hole, the drilling part of that job takes a couple of minutes. The time you save compounds across a whole room, and a bit that cuts easily also puts less strain on you and your battery. You’ll notice it most on jobs like these:

  • Running wire through a long row of studs

  • Boring holes for drain or supply lines through several joists

  • Drilling many matching holes in framing lumber for a shop project

Where it matters less

If you only need one or two holes, a few seconds either way won’t change your day. In that case, pick the bit for the hole size and finish you need. Speed is the reason to choose Speedbor when you have a pile of framing to get through.

Where spade bits fall short

Speedbor spade bits are built for boring wood, so keep them out of metal, and expect rougher holes than you’d want on furniture people will look at. They earn their place on framing and utility jobs where nobody sees the hole. For anything else, plan on a different bit.

Wood only

The Speedbor line is sold as woodboring spade bits, and the cutting edge is designed for aggressive removal of wood chips [2]. A flat spade with a center point has no way to cut steel or aluminum, and trying will dull the edges fast and can damage the bit.

If your drill path runs into a nail or screw buried in an old stud, stop and move the hole. For a metal bracket, steel stud or pipe strap, switch to a bit made for metal.

Rougher holes than a Forstner bit

A spade bit scrapes the wood out with two flat cutting edges, which leaves a rougher wall and often some tear-out where the bit exits. That’s fine inside a wall cavity. It’s a problem on a tabletop, cabinet face or shelf where the hole shows.

A Forstner bit is the better pick for visible work. It cuts a smooth, flat-bottomed hole with clean edges, which suits things like concealed hinge cups or a neat recess in a box lid. It’s slower and usually costs more per bit, so many woodworkers keep spade bits for rough holes and Forstner bits for finish holes.

Keep control of the drill

The same aggressive cutting that makes these bits fast also lets them grab [2]. When a bit bites hard, especially a larger size or one that hits a knot, the drill can twist suddenly in your hands.

A few habits keep you in control:

  • Grip the drill with both hands, using the side handle if your drill has one.

  • Clamp small or loose workpieces to a bench instead of holding them by hand.

  • Start at a moderate speed and let the bit cut without heavy pushing.

  • Ease off pressure as the point breaks through the back side, since that’s when the bit is most likely to catch.

  • Keep your wrist straight and your body braced so a sudden twist doesn’t wrench your arm.

Should you buy a set or single sizes?

Buy a set if you drill holes of different sizes for different jobs, and buy single bits if you keep reaching for the same one or two sizes. A set costs more up front but saves you a trip to the store when a project calls for a size you didn’t plan on.

The 8-piece set with case

The 8-piece Speedbor Blue Groove Pro set starts at 3/8 in. and steps up through 1/2 in., 5/8 in. and 3/4 in. into the larger sizes [4]. It comes with a case, so the bits stay sorted by size and their edges don’t knock against loose hardware in a drawer [4].

This set fits you if you do a mix of small and medium holes: a 3/8 in. hole for a thin cable, a 5/8 in. hole for a bundle of wires, a 3/4 in. hole for a supply line. Having them all in one case means you grab the right size instead of making do with the closest one.

There is also an 8-piece set of 6-inch bits with a case, ranging from 3/8 in. up [5]. Pick that version if you often bore through thick stock and want the extra length in every size.

The 10-piece assorted set

Irwin also sells a 10-piece assorted Speedbor set [2]. Two extra bits give you more sizes to choose from, which helps if you take on varied projects, like running cable one weekend and building a workbench the next.

If you’re setting up a general shop and don’t know yet which sizes you’ll use most, this is the safer pick. You’ll likely find that a few bits do most of the work, and the rest are there when an odd size comes up.

When single sizes make more sense

Buy singles if one job dominates your drilling. A plumber or remodeler who bores 3/4 in. holes through studs for pipe all day will wear out that one bit long before the others in a set get dull.

Keep a spare or two of your most-used size on hand. When it dulls in the middle of a job, you swap bits and keep going instead of stopping to sharpen.

Picking your first Speedbor bit

Buy the bit sizes your next project actually calls for, and add more only when a job needs them. If you’re running a single cable or pipe through a few studs, one or two bits in those diameters will cover it, and you won’t pay for sizes that sit unused in a drawer.

If you drill holes for all kinds of jobs around the shop, a set makes more sense. The standard 8-piece set starts at 3/8 inch and moves up through 1/2, 5/8 and 3/4 inch [4]. The 6-inch version has the same 8 sizes plus a case [5]. Before you buy, compare current prices at a couple of U.S. retailers, since sets and single bits are both widely stocked.

Sources

  1. Spade Bits | IRWIN

  2. IRWIN Speedbor 10-Piece x Assorted Woodboring Spade Drill Bit Set …

  3. IRWIN SPEEDBOR Woodboring Spade Drill Bit

  4. IRWIN Tools Speedbor Blue Groove Pro Spade Bit Set with Case, 8-Piece …

  5. IRWIN® Speedbor® 6″ Spade Drill Bit Set – 8 Piece

  6. Irwin Speedbor Spade Bits Review