The Kreg 520PRO is a handheld pocket hole jig that suits DIYers and hobbyists who build or fix things now and then, often right where the project sits. It works on stock from 1/2″ to 1-1/2″ thick, so your board needs to fall in that range before the jig is any use [1]. It also helps to read Porter Cable PC560 Quik Jig: What It Is and Who It Suits.
Because you carry the jig to the work, you can add a pocket hole to a cabinet that’s already assembled or tighten up a wobbly bookshelf without taking it apart. If you plan to drill dozens of matching holes for a run of face frames, a bench-style jig in the shop will serve you better.
Below you’ll find how the 520PRO works, its standout features, the projects it fits and where it falls short.
What is the Kreg 520PRO and how does it work?
The Kreg 520PRO is a handheld pocket hole jig from Kreg: a small guide you clamp onto a board so your drill bores a hole at a steady, shallow angle [2]. You then drive a screw through that hole into a second board to join the two. Because the jig is handheld, you bring it to the wood, rather than carrying every board to a bench-mounted unit. It also helps to read Kreg Drilling Guide KDG-6000: What It Does and Who Should Buy It.
What a pocket hole is
A pocket hole is a hole drilled at an angle into the face of one board so it exits through that board’s edge or end. The screw sits low in this angled “pocket,” and its tip comes out the edge and bites into the neighboring piece. Picture a bookshelf: you drill pockets into the underside of a shelf near each end, then screw up through them into the side panels.
This kind of joint is popular because it needs no glue-up clamps held for hours and no complex cuts like dovetails or mortises. The screw head stays hidden on the back or underside of the work, so the visible faces look clean.
How the process goes
The basic workflow has four parts:
Clamp the 520PRO to the board where you want the joint, with the jig’s guide set for your stock thickness.
Drill through the jig’s guide with a stepped pocket hole bit in your drill. The jig holds the bit at the correct angle, so you don’t have to judge it by eye.
Remove the jig and line the drilled board up against the second board.
Drive a pocket hole screw through the angled hole into the second board until the joint pulls tight.
On a face frame, for example, you would drill pockets into the ends of each rail, then screw the rails into the stiles. The jig handles the angle, and your drill and driver do the cutting and fastening.
Which features stand out?
Two features set the 520PRO apart from a basic handheld jig: the way it clamps to your board and the way you hold it. Kreg lists VersaGrip clamping and a 360-degree rotating handle as its headline features [2]. Both aim at the same problem, which is keeping a small jig steady while you drill.
VersaGrip clamping
VersaGrip is Kreg’s name for the jig’s clamping system, which the company describes as intuitive [2]. In practice, a handheld jig needs to lock onto the workpiece so it doesn’t creep sideways when the drill bit starts cutting. A quick, simple clamp means you spend less time fiddling between holes. That matters when you’re drilling a dozen holes for a set of shelf rails.
360-degree rotating handle
The handle rotates a full 360 degrees [1]. That lets you turn the grip to whatever angle feels natural, whether you’re drilling on a bench, on the floor, or reaching into a cabinet that’s already assembled. For example, if you’re adding a pocket hole near the back of a face frame, you can swing the handle out of the way of the side panel instead of twisting your wrist.
GripMaxx technology
The Amazon listing also names GripMaxx technology as a feature [3]. The listing doesn’t spell out how it works. Read it as part of the jig’s grip system and judge it on how well the jig holds when you use it.
What owners say
Owners rate the 520PRO 4.7 out of 5 on both Kreg’s site, from 227 ratings, and Lowe’s, from 48 ratings [2][1]. A score that high on two separate stores suggests most buyers are happy with how it performs. The Kreg count is the larger sample, so lean on it more than the Lowe’s figure.
What wood thickness and projects does it handle?
The 520PRO is rated for stock from 1/2″ to 1-1/2″ thick, which takes in the two materials most DIY builds use: 3/4″ plywood and 2x lumber. [1] That range keeps most home shop and around-the-house projects within reach. [3]
Plywood and 2x lumber
A “2×4″ is not 2 inches thick. Dimensional lumber is milled down, so a 2×4 or 2×6 measures about 1-1/2″ thick, which sits at the top of the jig’s range. Standard 3/4″ plywood and 1x boards (about 3/4” actual) fall in the middle.
In practice, you can join a 2×4 workbench frame and a 3/4″ plywood cabinet box with the same jig. Set the jig and your drill bit’s depth collar to the thickness you’re drilling before each job, since a mismatch puts the screw tip too close to the face or leaves it too short to bite.
Projects that fit
The range suits the builds homeowners and hobbyists take on most often:
Wall and closet shelves in 3/4″ plywood or 1x pine
Face frames for cabinets, where the screws hide on the back side
Cabinet boxes and built-ins
Furniture repairs, such as a loose table apron or a wobbly chair rail
Outdoor benches and planters in 2x lumber
Repairs are where a handheld jig earns its place. You can clamp it to a part that’s already assembled, which a fixed jig can’t reach.
Stock outside the range
Anything thinner than 1/2″ or thicker than 1-1/2″ is outside what the 520PRO is rated for. [1] That rules out 1/4″ hardboard backs, thin drawer bottoms and true 4×4 posts.
For those parts, use another joint. Glue and brad nails work for thin panels, and a 4×4 post can take lag screws, dowels or a metal bracket.
Where does a handheld jig fall short?
A handheld jig trades speed and repeatability for portability: you place it by hand for every hole, so long runs of identical joints take longer and drift more than on a fixed bench jig. For a few joints on a repair or a single shelf, that hardly matters. For a stack of face frame parts, you will feel it.
Repositioning slows batch work
Each pocket hole means a full cycle: line the jig up on the board, clamp it, drill, unclamp, then move to the next spot. A bench jig stays put, so you only slide the workpiece in and drill. If a bookcase needs 24 pocket holes, you repeat that setup 24 times with the 520PRO.
The VersaGrip clamping on the 520PRO is meant to make each of those cycles quicker. [2] It shortens the steps, but you still go through all of them for every hole.
You need a steady hold and a drill
The jig doesn’t make holes by itself. You run a drill through it, so you have to keep the jig firmly in place while the bit cuts. On a narrow rail or a small offcut, that can mean clamping the board to a sawhorse or workbench first so it doesn’t spin while you drill.
The 360-degree rotating handle lets you turn your grip to suit the angle you’re working from. [2] That helps in tight spots, such as inside a cabinet, but your hands still do the holding that a bench jig’s base does for you.
Less repeatable on long runs
Because you set the jig on each board by eye, small differences creep in from one hole to the next. Across ten matching rails, one hole might end up slightly closer to the edge than the others. On a single repair you’ll never notice. On a run of cabinet doors, a fixed bench jig with a stop puts every hole in the same spot without you measuring each time.
Should you pick a bench-style jig instead?
Pick a bench-style jig if you drill dozens of pocket holes per session in a shop, and keep the 520PRO if you carry your tools to the job or build a few projects a year. The table below lays out the trade-offs.
Criterion | Kreg 520PRO (handheld) | Bench-style jig |
|---|---|---|
Portability | Fits in a tool bag and goes to the job site | Stays on a bench, heavier to move |
Setup | Clamp it on the board and drill | Set once on the bench, then feed boards through |
Volume | Best for a handful of joints at a time | Built for repeated holes in a batch |
Workpiece size | Works on large panels you can’t lift onto a bench; rated for 1/2″ to 1-1/2″ thick stock [1] | Workpiece has to fit in the jig’s clamp area |
The handheld jig moves to the wood. The bench jig makes the wood come to it. That one difference drives everything else in the table.
When the 520PRO is the better pick
Choose it for on-site work and occasional builds. Say you’re adding a face frame to a built-in closet cabinet or reinforcing a wobbly shelf in a spare room. You clamp the jig right onto the installed piece, and the 360-degree rotating handle lets you hold it at whatever angle the space allows [2].
It also suits a full sheet of 3/4″ plywood that is too awkward to wrestle onto a bench jig.
When a bench jig is the better pick
Choose a bench jig if you build in batches in a shop. Twenty cabinet face-frame rails go faster when each board slides into the same fixed stop instead of getting a fresh clamp-and-drill setup.
The Porter-Cable PC560 is one bench-style alternative to look at if you work this way.
Common questions about the 520PRO
Most of what people ask about the 520PRO before buying comes down to what’s in the box, where to get it and whether it handles thin stock. Here are short answers to those questions.
Does the 520PRO come with screws?
The Amazon listing for the Kreg Pocket-Hole Jig 520 names 60 screws in its title [3]. That’s enough to finish a small first project, such as a simple shelf or a couple of face frames, before you need to buy more.
For anything bigger, plan on picking up a box of pocket screws sized for your wood. If the screw count matters to you, read the box contents on the listing you’re actually ordering from, since a bundle sold by one store may differ from another’s.
Where can you buy it in the U.S.?
You can buy the 520PRO straight from Kreg’s own store [2]. It’s also sold on Amazon [3] and at Lowe’s [1].
Buying from Lowe’s lets you pick it up locally and see the jig in person if your store stocks it. Amazon is handy if you want the bundle that lists screws in the title. Prices move between these stores and with sales, so check the current price at each before you buy.
Can it join 1/2″ stock?
Yes. Kreg’s 520PRO is listed for material from 1/2″ to 1-1/2″ thick [1]. That means 1/2″ plywood for drawer boxes or small cabinet backs sits right at the bottom of what the jig is made for.
With thin stock, set the jig and your drill bit collar for 1/2″ material before you drill. Matching the setting to the board keeps the screw tip from breaking through the face of the second piece.
Is the 520PRO worth buying?
Buy the 520PRO if you build a few projects a year, fix furniture, or need a jig you can carry to the job. It clamps onto the board where it sits, so you can drill pocket holes in a cabinet you’re installing or a bookshelf already in the room. For a garage builder making a set of shelves this month and a face frame next spring, that flexibility beats a jig bolted to a bench.
If you plan to drill dozens of identical holes in one session, put your money toward a bench jig instead. Before you order, measure the boards you use most and make sure they fall within the jig’s 1/2″ to 1-1/2″ thickness range. [3]