Nova Voyager DVR Drill Press: Who It Suits and What to Know

The Voyager DVR is an 18-inch belt-free drill press that changes speed with a dial and handles wood, metal, plastics and glass. Here is who it suits and where it falls short.

Nova Voyager DVR Drill Press: Who It Suits and What to Know
In this article

The Nova Voyager DVR drill press is worth it if you drill a mix of materials and want speed changes without moving belts around. It is an 18-inch variable-speed press, SKU 58000, built to handle wood, metal and plastics in one machine [1]. If you only drill wood and want to keep costs down, a simpler press may cover you.

What sets your Voyager apart is its belt-free direct drive, which gives clean speed control and steady torque for accurate drilling [2]. That matters when one weekend you’re boring Forstner holes in oak and the next you’re drilling a steel bracket.

This review covers how the DVR motor works, the speed range, what it can drill, how it stacks up against belt-drive presses, its downsides and who should buy one.

How does the DVR motor work

The Voyager’s motor is a brushless direct-drive unit run by an onboard computer, so the press sets spindle speed electronically instead of through belts and pulleys. Knowing how it works helps you judge what you gain over a conventional drill press.

What DVR means

DVR stands for Digital Variable Reluctance, the motor technology Nova builds the Voyager around. [1] A reluctance motor turns its rotor by switching magnetic fields on and off in sequence. The digital part means electronics time that switching.

In practice, the electronics take over the jobs that belts and step pulleys do on a traditional press. You set a speed, and the controller drives the motor to hold it.

Brushless and belt-free

The Nova motor is brushless. [3] Brushes are small carbon contacts that wear down over time in many conventional motors. Without them, you have one less wear part to inspect or replace.

The Voyager is also beltless. [4] You never open a pulley cover to move a belt, and you have no belts to stretch, slip or replace. That matters most when you switch between jobs often, such as going from a Forstner bit in oak to a small bit in aluminum within the same afternoon.

Steady torque and clean speed control

Nova’s DVR drill presses deliver clean speed control and steady torque for accurate drilling. [2] Steady torque means the spindle keeps pulling through the cut instead of bogging down when a large bit bites into dense material.

The onboard computer

The Voyager has an onboard computer. [4] It runs Striatech’s ADAPTIVE CONTROL™, which manages the motor while you work. [5] Think of it as the brain that keeps the motor responding to the load, so you can concentrate on feeding the bit and holding the workpiece.

Close-up of the motor housing on top of a drill press head, with cooling vents and a power cable clearly visible.

What speed range do you get

You get a speed range of 50 to 3000 RPM, and you set it by turning a dial. [4] That covers everything from a slow crawl for big cutters to a fast spin for tiny bits, without opening the head of the machine.

Small steps, no belts to move

The Voyager is beltless, so speed changes are quick and come in small increments. [4] On a belt-drive press you get a fixed set of steps, and changing between them means stopping the machine, lifting the cover and moving a belt across pulleys.

With the dial, you can nudge the speed up or down while you watch how the cut behaves. If a bit starts to chatter or a hole edge starts to burn, you adjust a little and keep going. You are not stuck choosing between two preset speeds that are both a bit wrong.

Which end of the range to use

The general rule is simple: the bigger the bit and the harder the material, the slower you run it. Small bits in soft material can spin fast.

Some everyday examples:

  • A large Forstner bit or hole saw in hardwood works best near the low end, where it cuts cleanly without scorching.

  • Drilling steel or aluminum calls for low speeds so the bit stays cool and keeps its edge.

  • A 1/8-inch twist bit in pine or plywood can run near the top of the range for a clean, quick hole.

  • A mid-size brad-point bit in wood sits comfortably in the middle.

Because the Voyager goes as low as 50 RPM, you have room for slow, heavy cuts that many belt presses can’t reach at their lowest pulley setting. [4] At the other end, 3000 RPM gives small bits the speed they need for clean entry in wood. [4]

A woodworker's hand presses a button on a drill press control panel to change the spindle speed before drilling.

What materials can it drill

The Voyager DVR drills wood, metal, plastics and glass, so one machine can cover most of the materials a home shop sees. [5] Teknatool describes it as the most versatile drill press on the market, which is the maker’s own claim rather than an independent test. [1] What matters for you is that you don’t need a second press for the occasional metal or acrylic job.

What that looks like in a home shop

Wood is the everyday case. You might bore shelf-pin holes in a bookcase side, cut hinge cups for cabinet doors with a Forstner bit, or drill dowel holes for a chair joint.

Metal comes up more often than most woodworkers expect. Typical jobs include drilling mounting holes in a steel bracket, enlarging a hole in an aluminum plate for a jig, or drilling through angle iron for a shop cart.

Plastics and glass fill in the rest. You could drill acrylic for a dust-collection blast gate or a router-table insert, or drill a glass bottle or jar for a lamp or a craft project. These materials tend to crack or melt if the speed is wrong, so a press that changes speed easily is a real help here.

Who else uses it

Trades that do precise, varied drilling use it too. A piano technician has reviewed the Voyager DVR. [4] Piano repair mixes hardwood, felt-covered parts and metal pins in small, exact holes, and that kind of mixed, detail-heavy work is a good test for any drill press.

If your projects jump between materials like this, the Voyager’s range lets you finish them on one machine. If you only ever drill pine and plywood, this range is less of a reason to buy it.

How does it compare with a belt-drive drill press

The biggest practical difference is how you change speed: on the Voyager you turn a dial, and on a belt-drive press you stop the machine and move belts between pulleys. The Voyager is beltless, so you can shift RPM quickly in small steps by turning that dial [4]. On a typical belt press, going from a slow speed for a 2-inch Forstner bit to a fast one for a 1/8-inch twist bit means opening the head cover and repositioning the belt each time.

Motor and power

The Voyager uses a brushless motor, while conventional presses run a standard motor through belts and pulleys [3]. Nova pitches its DVR presses as belt-free with clean speed control and steady torque [2]. In practice, that means you don’t have belt tension to set, and you don’t get the stepped speed jumps that pulleys impose.

Raw power is close between the Voyager and a strong belt-drive rival. The Laguna DP20 is rated at 1.5HP, and the Voyager can reach a 2HP rating when it’s connected to 240V [3]. That extra half horsepower gives you more headroom for large bits in hardwood or steel, as long as your shop has a 240V circuit.

Criterion

Nova Voyager DVR

Belt-drive press (e.g., Laguna DP20)

Speed changes

Turn a dial, small increments

Stop and move belts between pulleys

Motor

Brushless, direct drive

Conventional motor with belts

Power rating

2HP on 240V

1.5HP (Laguna DP20)

The Voyager wins on convenience and fine speed control, and it edges ahead on power if you wire it for 240V. A belt press trades that convenience for a simpler mechanical design.

Who should still pick a belt-drive press

A belt-drive press still makes sense if you drill mostly wood at one or two speeds and rarely change bits. In that case you’d seldom touch the belts, so the dial’s main advantage goes unused. It also suits you if you’d rather fix a worn belt or pulley yourself than troubleshoot electronics.

What are the downsides

The biggest catch with the Voyager DVR is power: to get its full 2HP rating, you need to connect it to 240V. [3] If your shop only has standard 120V outlets, plan on either running a 240V circuit or accepting that you won’t get the top rating the press is known for.

Plan for a 240V circuit

Many garage and basement shops in the U.S. have 240V only where a dryer, range or larger table saw lives. If the spot where you want the drill press has just ordinary wall outlets, adding a 240V circuit is a job for a licensed electrician and an added cost on top of the machine.

Think about where the press will sit before you buy. A drill press is heavy and hard to move once it’s set up, so it should go near the outlet it needs. Running an extension cord across the floor to reach a distant receptacle is a poor fix in a busy shop.

More electronics, more to go wrong

The Voyager relies on a motor controller and onboard electronics. A plain belt-drive press has very little that can fail. With a belt press, a worn belt or a noisy bearing is a cheap part you can often swap yourself on a Saturday afternoon.

A fault in a control board is a different kind of repair. You usually can’t diagnose it with a wrench and a multimeter, and you may need replacement parts or service through the dealer. If you like fixing your own tools, that matters. Ask the seller what kind of support and parts availability they offer before you commit.

Price it against the alternatives

The Voyager costs more than many belt-drive presses, and prices shift between dealers and sales. Check the current price at a few U.S. dealers, then decide whether dial speed control is worth the difference for the kind of drilling you do.

Common questions about the Voyager DVR

Does it run on 120V?

You can likely run it on a standard household circuit, but plan your wiring before the press arrives. The Nova can be connected to 240V to reach its 2HP rating, which suggests 240V is an option for more power rather than the only way to run it. [3]

In practice, that leaves you two setups. On a regular shop outlet you run the press below its top rating. If you want the full output for big bits in steel, you need a 240V circuit near the press, which in many garages means an electrician adds a dedicated line.

Ask the dealer which plug the machine ships with and what output to expect on your circuit. Your answer decides whether the press goes straight into service or waits for new wiring.

Is there a Viking model too?

Yes. Nova sells its DVR drill presses as Voyager and Viking models, and both use belt-free power with clean speed control and steady torque. [2]

If you’re shopping, compare the two side by side at a Nova dealer. Look at the size of the work you drill, how much table and throat room you need and how much floor space you have, then pick the model that fits your shop.

Where is the manual?

Teknatool International, the company behind Nova, posts the NOVA Voyager DVR Drill Press Manual on its online support site. [5] To find it, search the Teknatool support pages for that title.

Read it before you buy as well as after delivery. It shows you how the press is set up and controlled, which helps you judge whether the machine suits the way you work.

Should you buy one

Buy the Voyager DVR if your projects move between wood, metal and plastic and you want to change speed without opening the head. Its beltless design lets you dial anywhere from 50 to 3000 RPM in small steps [4], so going from a large bit in steel to a small bit in maple takes a turn of the dial.

If you only drill wood and want to spend less, a belt-drive press does that job well, and moving a belt now and then costs you only a minute.

Before you order, look at the outlet where the press will sit. The Nova reaches its 2HP rating only when it is connected to 240V [3], so find out whether your shop has a 240V circuit or whether you will need an electrician to add one.

Sources

  1. NOVA VOYAGER DVR 18″ VARIABLE SPEED DRILL PRESS (SKU 58000)

  2. Nova Drill Presses | DVR Smart Direct-Drive …

  3. A very serious Nova Voyager competitor…Laguna DP20

  4. Nova Voyager DVR Drill Press Review from a Piano Technician

  5. NOVA Voyager DVR Drill Press Manual – Teknatool International