Power Tool Battery Adapters: What They Do and When to Use Them

A battery adapter lets you run tools from one brand on batteries you already own from another. Here is how they work, which combinations exist, and the fit, warranty and safety limits to weigh first.

A collage of power tool battery adapters, including a yellow DeWalt adapter, black and red 18V adapters, and one fitted to a drill.
In this article

Yes, you can often run one brand’s tool on another brand’s battery by using a power tool battery adapter. It works only when an adapter exists for your exact battery and tool pairing, and it comes with limits you should weigh first.

An adapter sits between your battery and the tool, so the batteries you already own can power another brand’s tools. [1] Adapters are sold for pairings among DeWalt, Milwaukee, Makita, Ryobi and more. [2] That matters when the best combo kit deal is on a different platform than your current tools: say your shelf is full of Ryobi packs and a DeWalt kit is on sale.

The trade-offs come down to fit, voltage, warranty and safety. Below you’ll see how adapters work, which brands they cover, and when switching platforms is the better move.

How does a battery adapter work?

A battery adapter is a small housing with two different ends. The top is shaped like the base of the battery’s own brand of tool, so your pack slides on and latches just as it would on a drill from that brand. The bottom copies the battery of the tool you want to run, so it slides into that tool’s foot like a native pack.

Two ends, one connection

Each end has to match two things: the rails and the terminals. Rails are the grooves and ridges that guide the battery into place and let the latch click shut. Terminals are the metal contacts that carry current.

Say you own 18V Ryobi batteries and pick up a DeWalt tool. The adapter’s top takes the Ryobi pack, and its bottom fits the DeWalt tool. Inside, wiring links the battery’s terminals to the matching terminals on the tool side. Adapters are made for pairings such as 20V DeWalt, 18V Milwaukee and 18V Ryobi batteries. [3] They let your existing batteries power tools from other brands. [1]

Power goes one way only

The adapter passes the battery’s current straight through to the tool. It does not charge anything, so the pack still goes back on its own brand’s charger when it runs low. Think of it as an extension of the battery’s connector.

Step-down adapters for lower-voltage tools

Some adapters do more than reshape the connection. Step-down converter versions bring an 18V or 20V pack down to a lower voltage. [3] That lets a full-size battery run a lower-voltage tool that would otherwise take a smaller pack.

A straight-through adapter has no circuitry to reduce voltage. Whatever the battery puts out is what the tool receives. When the voltages differ, you need the step-down type.

Close-up of a battery adapter's metal contact terminals next to a lithium battery pack, showing how the two connect.

Which brands and voltages do adapters cover?

Most adapters you’ll find connect the four big U.S. platforms: DeWalt, Milwaukee, Makita and Ryobi. If your batteries and the tool you want come from two of these brands, you have the best chance of finding an adapter for that exact pairing. Sellers list these brands first for that reason [2].

Common pairings

Adapters are usually sold by direction: the battery brand you own, then the tool brand you want to run. One retailer stocks adapters for 20V DeWalt, 18V Milwaukee and 18V Ryobi batteries [3]. That covers setups like these:

  • A DeWalt 20V battery running a Milwaukee 18V tool

  • A Milwaukee 18V battery running a Ryobi 18V tool

  • A Ryobi 18V battery running a Makita 18V tool

A single adapter works in one direction only. If you want to run DeWalt tools on Milwaukee packs and Milwaukee tools on DeWalt packs, you need two different adapters.

Wider brand coverage

Some sellers go well past the big four. One shop offers adapters for 44 brands and has a finder that matches your battery to your tool [2]. If you own a less common platform, a finder like this is the quickest way to see whether your combination exists at all, so you don’t have to scroll through hundreds of listings.

Adapters from the tool makers

Third-party shops aren’t the only source. Lowe’s carries a DeWalt 20-Volt Adapter and a Metabo HPT MultiVolt 36-Volt 1-Pack Adapter [4]. Branded adapters like these usually connect packs within the maker’s own lineup, such as older and newer packs. They generally won’t link two competing brands.

Inverter-style adapters

Some products listed as battery adapters convert DC 18V to AC 110V output [5]. These turn a tool battery into a small power source for a plug-in device. That makes them a separate category from a battery-to-tool adapter, so read the listing closely before you order one by mistake.

An assortment of cordless power tool batteries in different colors and sizes lined up on a garage workshop shelf.

Will the adapter fit and perform well?

An adapter can fit your tool and still change how it handles, so think about balance, latch security and the kind of work before you rely on one. The adapter is an extra block between the battery and the tool. That adds height and weight below the grip, which shifts the balance point.

Balance and handling

You’ll feel the change most on tools you hold at arm’s length or overhead. A drill driving screws into a ceiling joist gets bottom-heavy, and a compact impact driver loses some of its reach into tight spots like between studs or under a cabinet. On a tool that sits on its base, such as a small sander used on a bench, the extra height matters less.

Latch fit

The adapter needs to click firmly onto the tool and hold the battery just as firmly. A loose latch lets the battery wobble with every vibration, which can interrupt power mid-cut or let the pack drop off the tool. Before a job, grab the battery and give it a firm tug and twist. It should not shift on the adapter or on the tool.

High-draw tools

Saws push an adapter harder than most tools. A circular saw ripping a 2×10 or a reciprocating saw cutting through framing pulls far more current than a drill sinking a few screws, and all of that current passes through the adapter’s contacts. Lighter tools like work lights, inflators and drivers are an easier match.

Voltage class

Match the battery’s voltage class to the tool’s. Adapters are commonly sold for 20V DeWalt, 18V Milwaukee and 18V Ryobi batteries [3]. In general, 18V and 20V packs belong to the same nominal family, with the different numbers coming from how each brand labels its packs. A 36V or 12V tool is a different class and needs a matching or step-down adapter.

What are the warranty and safety risks?

The biggest risk with a third-party adapter is heat: an adapter that isn’t built to the tool maker’s spec may not pass along the signals that let the battery and tool protect themselves. Most lithium-ion packs and tools communicate to cut power when a battery gets too hot or drains too low. If an adapter skips that handshake, the pack can keep delivering current past the point where it would normally shut off, which can overheat or damage the battery, the tool or the adapter itself.

Watch for heat while you work

After a few minutes of use, touch the battery and adapter. Warm is normal under load, especially with a circular saw or grinder. If either feels hot, smells like burning plastic or starts to discolor, stop, remove the battery and let everything cool in an open spot away from anything flammable.

Give the tool short breaks during long cuts. Ripping a full sheet of plywood draws far more current than driving a few screws, so heavy work is where trouble shows up first.

Expect warranty limits

Tool and battery makers can turn down a warranty claim when damage involves a third-party adapter.

Pick a well-built adapter

Choose an adapter with a latch that clicks firmly into both the battery and the tool, with no rocking. A battery that works loose mid-cut is a hazard. Buy from a reputable seller with clear product details and contact information; some specialty sellers advertise their adapters as reliable and secure [6], but test the latch yourself when it arrives.

Don’t leave it unattended

Remove the battery from the adapter when you finish, and never leave an adapted battery charging or sitting in a tool overnight. Store batteries and adapters apart in a cool, dry place.

Should you buy an adapter or switch platforms?

Buy an adapter when you need one or two tools from another brand and already own a good set of batteries. If you’re about to buy several tools on a second platform, switching or committing to one brand usually works out better.

When an adapter is the right call

An adapter earns its place for a tool you use now and then. Say your drill, impact driver and circular saw all run on Milwaukee packs, and you find a Ryobi glue gun or a DeWalt oscillating tool you like. An adapter lets you run that one tool from batteries you already own, so you skip buying a second charger and battery set. [1] Adapters cover pairings among DeWalt, Milwaukee, Makita, Ryobi and other brands. [2]

This works best for light, short jobs: a few cuts with a multi-tool, an afternoon with a sander or a cordless inflator in the garage. The adapter is a bridge for gaps in your kit. It doesn’t make two platforms into one.

Why mixing many brands gets messy

Every extra brand you adapt adds another adapter to keep track of and another connection that has to fit well. With three or four adapters in the shop, you spend time hunting for the right one before each job, and each adds a point where a battery can sit loose.

The risk grows too. Each adapted tool is another place where fit, balance and warranty questions come up. If you find yourself adapting most of your tools, the adapter is covering for a platform choice you haven’t made yet.

When a combo kit beats adapting

If you need several new tools, a combo kit on one platform often costs less per tool than buying them bare and adapting them. Kits usually include batteries and a charger, so you start with a full working set and no adapters in the chain. The combo kit deals overview walks through how to judge whether a kit is a good value for you.

Battery adapter questions readers ask

Can an adapter let me charge a battery in another brand’s charger?

No. A battery adapter connects a battery to a tool, so it only works in the space between the pack and the tool’s battery slot. For example, if you own Milwaukee 18V packs and a DeWalt 20V drill, the adapter lets the drill run on the Milwaukee pack, but you still charge that pack on the Milwaukee charger.

The adapters sold for this purpose are built around tool brands and battery platforms. Common listings cover 20V DeWalt, 18V Milwaukee and 18V Ryobi batteries. [3] Keep one charger for each battery brand you own, and charge the batteries off the adapter.

Do adapters reduce run time?

The energy you get comes from the battery. Run time depends on the pack’s capacity and on how hard the tool works it. If a 5.0Ah pack runs your circular saw for a certain number of cuts on its own platform, that same pack is still the limit when it powers a saw through an adapter.

If you want longer run time on the adapted tool, use a higher-capacity pack. A cheaper or different adapter will not change it. A small pack on a heavy saw empties quickly whether or not an adapter sits in between.

Are AC inverter adapters the same thing?

No. Some products listed as battery adapters convert a DC 18V battery to AC 110V output. [5] They are small inverters that let a tool battery run a corded device, and that is a different job from fitting a battery onto another brand’s cordless tool.

Read the listing before you buy. If you want to run a DeWalt drill on a Ryobi pack, you need a brand-to-brand adapter. An inverter-style unit with an AC outlet is the wrong product for that.

Picking the right adapter for your tools

Match the adapter to your exact battery brand, voltage and tool model before you order, because an adapter only works if both of its ends fit what you own. For example, write it down as “Milwaukee M18 battery to DeWalt 20V circular saw” and look for that exact pairing. Many sellers list adapters for DeWalt, Milwaukee, Makita, Ryobi and other brands, with a finder that matches yours. [2]

Use adapters for light, occasional jobs, like a brad nailer or a work light you pull out a few times a year. For saws and other tools you run every day, stay on one battery platform so every pack fits every tool without an extra part in between.

Sources

  1. Cordless Power Tool Battery Adapter Converters

  2. Power Tool Battery Adapters for 44 Brands

  3. Battery Adapters compatible with DeWalt Milwaukee Ryobi – DAIER

  4. Adapter Power Tool Batteries & Chargers at Lowes.com

  5. Power Tool Battery Adapter

  6. Power Tool Battery Adapters | Dewalt, Milwaukee, Makita & Ryobi …