Best Bench Planer: 5 Benchtop Thickness Planers for Home Shops

The DEWALT DW734 is the first pick for a smooth finish and less snipe. Here are four more benchtop planers and what to look at before you buy.

DEWALT Benchtop Planer, 15-Amp, 12-1/2-Inch, 3-Knife Cutter, 20,000 RPM, Corded (DW734)
In this article

The DEWALT DW734 is the first pick for most home shops looking for the best bench planer. Its three-knife cutterhead makes 96 cuts per inch, and a four-column carriage lock cuts down the movement that causes snipe, the dip planers leave near the ends of a board. Together these give you a smoother surface straight off the machine and less waste trimmed from each end. Learn more in Best Planer for Home Use: Five Picks and How to Choose.

A benchtop planer takes rough or uneven boards and brings them to one even thickness, so you can mill your own lumber instead of paying for pre-surfaced stock. Below are five picks in order, each matched to a different need, followed by a buying guide on capacity, knives and snipe.

We may earn a commission if you buy through links on this page.

As an Amazon Associate we earn from qualifying purchases.

How we picked: from products sold on Amazon for this need, compared by what their makers state and what buyers report in their reviews.

The Picks at a Glance

Product

Best for

Maximum rotational speed

Cutting width

Material type

Buyer rating

DEWALT DW734

a smooth finish

20000 rpm

12.5 in

Metal

4.7 of 5 (2,769 reviews)

Check price on Amazon

WOODERS 13-Inch Planer

wide boards

10000 rpm

13 in

Metal, Plastic

4.2 of 5 (60 reviews)

Check price on Amazon

WEN PL1252

budget-minded hobbyists

20000 rpm

12.5 in

Cast Iron

4.6 of 5 (527 reviews)

Check price on Amazon

CRAFTSMAN CMEW320

warranty peace of mind

8000 rpm

12.25 in

Carbon Steel

4.6 of 5 (1,520 reviews)

Check price on Amazon

VEVOR Two-Blade Planer

long stock

23500 rpm

15 centimeters

Cast Iron

4.5 of 5 (349 reviews)

Check price on Amazon

Buyer ratings as shown on Amazon on November 15, 2026; they change.

DEWALT DW734: Best for a smooth finish

DEWALT Benchtop Planer, 15-Amp, 12-1/2-Inch, 3-Knife Cutter, 20,000 RPM, Corded (DW734)

The DEWALT DW734 is the pick for woodworkers who want boards to come off the planer as smooth as possible, so there is less sanding before glue-up or finishing. Its three-knife cutterhead runs at 10,000 rpm and delivers 96 cuts per inch, which the maker calls one of the finest finishes of any portable planer. A four-column carriage lock also cuts down the movement that causes snipe, the dip planers leave at the ends of a board.

The maker lists a 15 amp, 20,000 rpm motor built for larger, deeper cuts in hardwoods. In practice, that means you can take a meaningful bite out of oak or maple without the motor bogging down on every pass. The knives are disposable and reversible, with 30% more knife life. When one edge dulls, you flip it instead of sending it out for sharpening, and you put off buying a new set.

The infeed and outfeed tables give 33-1/2 in. of material support. Longer boards stay level as they enter and leave the cutterhead, which helps against snipe on stock like 6-foot shelf boards. A material removal gauge and an extra-large thickness scale show how much you are taking off on each pass. That makes it easier to sneak up on a final thickness, such as 3/4 in., without overshooting.

Pros

  • Three knives give 96 cuts per inch for a smooth surface

  • Buyers say it works well out of the box and is easy to set up

  • Buyers report it handles soft pine through very hard species

  • A turret depth stop returns you to your most-used depths

Cons

  • Some buyers report gears breaking after about a month of use

  • Dust collection performs poorly for some owners

  • Some owners still get snipe at board ends despite the carriage lock

If you regularly plane boards wider than 12-1/2 in., look at the WOODERS 13-Inch Planer, which handles 13 inches against this model’s 12.5 inches.

Check price on Amazon

WOODERS 13-Inch Planer: Best for wide boards

13-Inch Benchtop Thickness Planer, 15A Wood Planer with 4 HSS Blades, 2000W All Copper Motor, Overload Protection for Woodworking

The WOODERS 13-inch planer suits you if your projects call for boards wider than 12-1/2 inches, such as tabletop panels or wide shelf stock. The maker lists a 13-inch maximum width and a 1/4 to 6.3 inch height range. That extra width lets a wide glued-up panel or a wide rough board go through without ripping it first.

The motor is a 15-amp, 2000W all-copper unit driving a 10,000 RPM cutterhead. In practice, the motor is meant to push through oak or walnut as well as pine. The cutterhead spins at half the 20000 rpm of the DEWALT DW734, so expect fewer cuts per inch and possibly a slightly rougher surface that needs more sanding.

The package has four HSS blades in total, counting the two extra replacement blades that come in a storage box. Spares on hand mean a nicked edge does not stop your project while you wait for an order. Built-in overload protection cuts power when the load gets extreme. If you push a hardwood board too deep, the planer shuts off instead of straining the motor. Each pass removes 0 to 1/8 inch, shown on a large depth indicator, and a dust port connects to your vacuum.

Pros

  • 13-inch capacity handles wider boards than the 12-1/2 inch picks

  • Two spare HSS blades in the box

  • Overload protection guards the motor

  • Oversized depth crank is easy on hands and wrists

Cons

  • At 60 pounds, it is heavy to lift onto and off a bench

If your boards are 12 inches wide or less and a smooth finish matters most, look at the DEWALT DW734 instead.

Check price on Amazon

WEN PL1252: Best for budget-minded hobbyists

WEN PL1252 15-Amp 12.5-Inch Two-Blade Benchtop Thickness Planer , Black

The WEN PL1252 suits hobbyists who want a full-size benchtop planer without stepping up to the pricier picks. It handles boards up to 6 in. thick and 12.5 in. wide, and buyers repeatedly call it good value for what it costs.

The maker lists a 15A motor that delivers 20,000 cuts per minute at a 26 ft per minute feed rate. In practice, a 6 ft board passes through in roughly 3 seconds, so surfacing a stack of rough lumber for a bookshelf moves along at a steady pace. You can set the depth anywhere from 0 to 1/8 in. per pass. Use the full 1/8 in. to hog off rough-sawn faces, then drop to a whisker-thin pass for the final surface.

The cutterhead carries two reversible 12.5-inch SK5 blades, model BP122K. Reversible means each blade has two edges: when one dulls, you flip it instead of buying new right away. Knowing the model number also makes ordering replacements straightforward.

Two blades do mean fewer cuts per inch than the three-knife DEWALT DW734 at the same 20,000 rpm. On figured or hard woods, that can leave slightly more visible marks that you will need to sand out.

Pros

  • Takes boards up to 12.5 in. wide and 6 in. thick

  • Buyers say it leaves a smooth finish, especially on softer woods like cedar

  • Buyers find it easy to use and quick for getting projects done

  • Reversible blades give two edges per set

Cons

  • Buyers report blades that can chip, which raises durability questions if you plane knotty or dirty stock

  • Buyers say it runs loud

  • Buyers mention snipe at board ends, so plan to cut a few inches off long pieces

If a glassy finish on hardwoods matters more than saving money, the DEWALT DW734 is the better fit.

Check price on Amazon

CRAFTSMAN CMEW320: Best for warranty peace of mind

CRAFTSMAN 12.25 In. Benchtop Thickness Planer, 15 Amp, Two Knife (CMEW320)

The CRAFTSMAN CMEW320 is the pick for a buyer who wants a longer safety net on a home-shop planer, because it carries a 3 Year Limited Warranty. It runs on a 15 amp motor meant for both hard and soft wood, so it handles oak and pine alike. A 12.25-inch cutting width fits typical shelf and tabletop boards.

The cutterhead uses two quick-change knives on a solid steel head mounted on ball bearings, which the maker says gives smooth operation and long life. Quick-change knives mean less downtime when an edge dulls in the middle of a project. A Poly-V drive turns the cutterhead for maximum stock removal, which helps when you are taking rough lumber down to size.

The knives are high carbon steel, double edged and reversible. When one edge wears, you flip the knife and keep going before you need new ones. A vacuum port lets you hook up a shop vac or dust collector, so chips go into a bag and stay off your floor.

Pros

  • 3 Year Limited Warranty

  • Reversible, double-edged knives for longer use between replacements

  • Buyers say it is easy to use and saves hours of sanding

  • Buyers find it a great value and well suited to small woodworking projects

Cons

  • Buyers report the height adjustment can shift while the planer runs, which matters when you need several boards at the same thickness

  • Buyers report snipe at the ends of boards, so plan to trim the ends of finished stock

  • Some buyers say their units broke down after little use, which is where the warranty earns its place

If a smooth finish matters more than warranty length, the DEWALT DW734 fits better, with a 20000 rpm cutterhead against this model’s 8000 rpm.

Check price on Amazon

VEVOR Two-Blade Planer: Best for long stock

VEVOR Thickness Planer Two-Blade, 12" Extended Infeeding Table

The VEVOR Two-Blade Planer is the pick if you often feed long boards, like 6- or 8-foot trim or tabletop stock. The maker lists table pull-out extensions that give 35 in. of total length for support on long stock, plus a cast iron bed. It takes boards up to 6 in. thick and 13 in. wide.

That 35 in. of support matters at both ends of a long board. A board that hangs off a short table tends to tip as it enters or leaves the cutterhead, and a flat, extended surface keeps it level so you spend less time holding the far end up. The precision machined cast iron bed and steel plate help keep boards flat, and cast iron adds mass that keeps the machine steady on your bench.

The 13 in. width lets you plane a wide glued-up panel or a 1×12 with room to spare. The cutterhead is a quick-change, solid steel two-knife design hardened to HRC55-60. HRC is a hardness scale, and harder knives hold an edge longer, so you sharpen or swap them less often. With two knives instead of three, expect fewer cuts per inch, so a slower pass or a light final sanding helps on show surfaces.

Pros

  • 35 in. of total table length for long boards

  • 13 in. width and 6 in. thickness capacity

  • Buyers say it works well on trim, baseboards and cutting boards

  • Buyers find it well made and good value for the money

Cons

  • Some buyers report that it removes material poorly or unevenly, which matters if you need consistent thickness across a batch

  • Two knives give a coarser cut than a three-knife head, so expect extra sanding on finish work

If a smooth finish straight off the machine is your priority, the three-knife DEWALT DW734 fits better.

Check price on Amazon

What should you look for in a benchtop planer?

Start with the widest and thickest boards you plan to run, because capacity is the one thing you can’t adjust later. Most benchtop planers take stock about 12-1/2 in. wide, while a few stretch to 13 in. That extra half inch matters when you surface wide tabletop boards or reclaimed lumber that won’t fit through a narrower machine.

Thickness capacity is usually around 6 in., enough for thick timbers and glued-up blanks.

Knife count and finish

More knives on the cutterhead mean more cuts per inch of board, which leaves a smoother surface. A three-knife head reaches 96 cuts per inch at its cutterhead speed. Two-knife machines make fewer cuts per inch, so expect a bit more sanding on figured or hard woods.

Snipe and table support

Snipe is a slightly deeper cut at the ends of a board, and long tables help prevent it by keeping the board level as it enters and leaves. Look for generous support: one model gives 33-1/2 in. of table, another 35 in. with extensions. A carriage lock that holds the cutterhead steady also cuts down on snipe.

Knives and dust port

Reversible, double-edged knives give you a second sharp edge before you buy replacements. A vacuum port lets you hook up a shop vac to pull chips away from the cutterhead.

Safety

Planers throw a lot of chips, so connect dust collection before you start and keep your face clear of the outfeed. Wear eye and hearing protection, since buyers repeat that these machines run loud.

Which planer is the right first buy?

DEWALT DW734 is the first pick if you want a smooth finish with less snipe on your first planer. Its three-knife cutterhead gives 96 cuts per inch, so boards come off needing less sanding before glue-up or finish. The four-column carriage lock cuts down the head movement that causes snipe, which means less wasted length trimmed off the ends of each board.

Your next step is to measure the widest board you plan to run through the machine. If your projects stay at 12-1/2 inches or narrower, the DW734 handles them. If you regularly work wider stock, that measurement points you to a 13-inch model before anything else.