Best Benchtop Planer: 5 Picks for Home Woodworkers

The DEWALT DW734 is the first pick for a smooth finish on hardwoods with less snipe. Four other planers cover spiral cutterheads, wider boards and tighter budgets.

DEWALT Benchtop Planer, 15-Amp, 12-1/2-Inch, 3-Knife Cutter, 20,000 RPM, Corded (DW734)
In this article

The DEWALT DW734 is the first pick for a fine finish on hardwoods. Its three-knife cutterhead makes 96 cuts per inch, so boards come out smoother and need less sanding. A four-column carriage lock cuts down the movement that causes snipe, the dip a planer can leave at the ends of a board.

A benchtop planer takes rough or uneven boards and brings them to one consistent thickness, so glue-ups close tight and parts match. That lets you buy cheaper rough lumber or reuse old boards instead of paying for pre-milled stock.

The other picks cover a spiral cutterhead for tricky grain, 13-inch models for wider boards, and budget two-knife planers for occasional projects.

As an Amazon Associate we earn from qualifying purchases.

How we picked: from products sold on Amazon for this need, compared by what their makers state and what buyers report in their reviews.

The Picks at a Glance

Product

Best for

Maximum rotational speed

Cutting width

Material type

Buyer rating

DEWALT DW734

smooth hardwood finishes

20000 rpm

12.5 in

Metal

4.7 of 5 (2,769 reviews)

Check price on Amazon

WEN PL1326

figured or tricky grain

10000 rpm

33 centimeters

Cast Iron

4.7 of 5 (746 reviews)

Check price on Amazon

CRAFTSMAN CMEW320

occasional home projects

8000 rpm

12.25 in

Carbon Steel

4.6 of 5 (1,520 reviews)

Check price on Amazon

WOODERS 13-inch planer

thick timbers

10000 rpm

13 in

Metal, Plastic

4.2 of 5 (60 reviews)

Check price on Amazon

VEVOR thickness planer

reclaimed wood

8000 rpm

13 in

Iron

4.3 of 5 (286 reviews)

Check price on Amazon

Buyer ratings as shown on Amazon on November 15, 2026; they change.

DEWALT DW734: Best for smooth hardwood finishes

DEWALT Benchtop Planer, 15-Amp, 12-1/2-Inch, 3-Knife Cutter, 20,000 RPM, Corded (DW734)

The DEWALT DW734 is the pick if you want planed hardwood that comes off the machine smooth enough to need little sanding. Its three-knife cutterhead spins at 10,000 rpm and gives 96 cuts per inch, one of the finest finishes of any portable planer. A four-column carriage lock also targets snipe, the dip some planers cut at the ends of a board.

The 15 amp motor handles larger, deeper cuts in hardwoods. On oak or maple you can take a fuller pass without bogging down, so you reach final thickness in fewer trips through the machine. The carriage lock drastically reduces the movement that causes snipe. Less snipe means you cut off less of each board’s ends and waste less lumber. Extra-long infeed and outfeed tables give 33-1/2″ of material support. They hold longer boards level as they enter and leave, so you need less help from a second person or roller stands.

The knives are disposable and reversible, with 30% more knife life and a fast, easy change. When one edge dulls, you flip it instead of sending it out for sharpening. A material removal gauge and extra-large thickness scale help you set each pass accurately, and a turret depth stop returns you to the depths you use most. That makes repeat batches, like a stack of 3/4 in drawer sides, quicker to match. It comes with a three-year limited warranty.

Pros

  • 96 cuts per inch for a smooth finish

  • Buyers say it works well out of the box and is easy to set up

  • Buyers report it handles everything from soft pine to very hard species

  • Reversible knives swap quickly

Cons

  • Some buyers report gears breaking after about a month of use

  • Dust collection performs poorly for some owners, and some still get snipe at board ends

  • Its 12.5-inch cutting width is narrower than the 13-inch WEN, WOODERS and VEVOR picks, which matters for wide tabletop boards

If you often plane boards wider than 12-1/2 in or work with wild, figured grain, the WEN PL1326 fits better.

Check price on Amazon

WEN PL1326: Best for figured or tricky grain

WEN PL1326 15-Amp 13-Inch Spiral Benchtop Thickness Planer

The WEN PL1326 is the pick if you plane figured maple, curly cherry or other boards whose grain changes direction and tears out easily. Its spiral cutterhead uses 26 staggered, rotatable HSS blades for a clean, smooth finish, and it takes boards up to 13 inches wide.

The maker lists boards up to 6 inches thick and 13 inches wide. That covers most furniture stock, from thin drawer sides to thick table legs, and the extra width over a 12-1/2-inch planer lets you run slightly wider panels in one pass. HSS means high-speed steel. Because the blades rotate, a nicked edge can be turned to a fresh one instead of replacing a whole knife.

A 15A motor drives the head at 10,000 RPM with a 26 feet per minute feed rate. At that feed, an 8-foot board takes about 20 seconds per pass. The planer comes with a depth stop and an adjustable dust port. The depth stop lets you plane several boards to the same final thickness, and an onboard material removal gauge shows how deep each pass cuts. Reading the gauge before each pass helps you take lighter cuts on tricky grain.

Pros

  • Spiral head with 26 rotatable blades for a smooth finish

  • 13-inch width and 6-inch thickness capacity

  • Buyers say it runs smoothly, leaves flat surfaces and shows little snipe at board ends

  • Buyers find it quieter than they expect and ready to use out of the box

Cons

  • It weighs 36.74 kg (about 81 pounds), so moving it between a shelf and the bench is a two-person job or needs a dedicated stand.

  • Its 10,000 rpm head speed is lower than the DEWALT DW734’s 20000 rpm.

If you mostly plane straight-grained hardwood and want the finest finish with a carriage lock against snipe, look at the DEWALT DW734 instead.

Check price on Amazon

CRAFTSMAN CMEW320: Best for occasional home projects

CRAFTSMAN 12.25 In. Benchtop Thickness Planer, 15 Amp, Two Knife (CMEW320)

The CRAFTSMAN CMEW320 is the pick if you plane boards now and then for shelves, small boxes or repair jobs and want a simple machine. It has a 15 amp motor that the maker rates for both hardwoods and softwoods, and a two-knife cutterhead built for quick blade swaps.

The maker lists a quick-change, solid steel cutterhead mounted on ball bearings, meant for smooth running and long life. Ball bearings help the head spin steadily, and a quick-change setup means less downtime when a knife gets dull or nicked. The knives are high carbon steel, double edged and reversible, so you can flip each knife to a fresh edge before you need to buy replacements.

A vacuum port for dust collection comes with the planer. Planers throw a lot of chips, so hooking up a shop vac keeps your garage floor cleaner and the chips off your next board. The 3-year limited warranty gives some cover for a tool you may use only a few weekends a year. For more detail, see Best Planer for Home Use: Five Picks and How to Choose.

Pros

  • Two-knife quick-change head on ball bearings

  • Reversible knives give two edges per knife

  • Buyers say it is easy to use and saves hours of sanding

  • Buyers find it a good fit for small woodworking projects

Cons

  • Some buyers report units breaking down after little use, and that the height adjustment can shift while running

  • Buyers mention snipe at the ends of boards, so plan to cut off a little extra length

  • The 12.25-inch cutting width is narrower than the 12.5 inches of the DEWALT DW734 and the 13 inches of other picks, which matters if you plane wide tabletop boards

If you plane hardwood often and want a finer finish, look at the DEWALT DW734 instead.

Check price on Amazon

WOODERS 13-inch planer: Best for thick timbers

13-Inch Benchtop Thickness Planer, 15A Wood Planer with 4 HSS Blades, 2000W All Copper Motor, Overload Protection for Woodworking

The WOODERS PL13-15AB is the pick for woodworkers who plane thick, wide stock, such as rough beam offcuts or slab pieces for a bench top. It takes boards up to 13 inches wide and has a height range of 1/4 to 6.3 inches. That means a thick timber that would bottom out other machines can still fit under the cutterhead.

The maker lists a 15-amp, 2000W all-copper motor that drives the cutterhead at 10,000 RPM. In daily use, a faster cutterhead takes more cuts per inch of board, which helps leave a cleaner surface on dense hardwoods like oak or walnut. The motor has built-in overload protection that cuts power under extreme loads. If you push a heavy cut through a wide board, the planer shuts off before it overheats, and you can take a lighter pass.

The planer comes with four HSS (high-speed steel) blades: the double-edged blades in the cutterhead plus 2 extra replacement blades in a storage box. With spares on hand, a nick from a hidden nail doesn’t stop your project while you order new knives. At 60 pounds, the machine stays put on a bench, but you’ll want help lifting it onto one.

Pros

  • Takes timbers up to 6.3 inches thick and 13 inches wide

  • Overload protection guards the motor

  • Spare blades and a dust port come in the box

Cons

  • At 60 pounds, it is heavy to carry to a jobsite or put away after each session

If a glass-smooth finish on hardwood matters more than thickness capacity, look at the DEWALT DW734 instead.

Check price on Amazon

VEVOR thickness planer: Best for reclaimed wood

VEVOR Thickness Planer with Foldable Iron Stand and Dust Exhaust

The VEVOR 13-inch thickness planer is the pick for people who want to clean up old, weathered or worn boards, and VEVOR built it with that kind of repurposing in mind. It pairs a 13-inch cutting width with a foldable iron stand, so you get a wide planer and a place to set it in one box.

The maker lists a 15 amp, 1800W motor with an 8000 rpm blade speed and a feed rate of 236 inches per minute. In practice, a 4-foot barn board passes through in well under half a minute, and the auto-feed pulls the board in so you only guide it. Two metal return rollers let you slide the board back to the infeed side for the next pass without walking around the machine.

The planer cuts boards up to 13 inches wide and from 0.2 to 6.3 inches thick. That covers wide salvaged tabletop planks and thick beam offcuts. A crank handle raises and lowers the cutter head, and a scale helps you set the depth. The stand detaches and the extension plates fold, so the planer can go against a garage wall between projects. A dust port with a 2-inch outer diameter connects to a dust collector, or you can fit the included iron dust cover instead. An over-current protector trips when the motor is overloaded.

Pros

  • 13-inch width and up to 6.3 inches of thickness for wide or chunky salvaged stock

  • The stand and folding tables come in the box

  • Buyers say it is a well-made machine overall and easy to use

Cons

  • Buyers report the drive belt breaking on the first day of use, which leaves you waiting on a part

  • Buyers find the stand’s assembly instructions poor and confusing

  • The 8000 rpm blade speed is lower than the 10,000 rpm of the WEN PL1326, so expect a slightly coarser surface between passes

If a smooth finish on figured hardwood matters more than capacity for reclaimed boards, look at the WEN PL1326 instead.

Check price on Amazon

What to look for in a benchtop planer

Start with the widest and thickest board you plan to run, because capacity is the one thing you can’t work around later. Most benchtop planers take boards 12-1/2 or 13 inches wide; the DW734 tops out at 12.5 inches, while the WEN PL1326 handles boards up to 13 inches wide and 6 inches thick. That extra half inch matters if you glue up panels or buy 13-inch-wide rough stock.

Next, look at the cutterhead. A straight-knife head uses a few long blades, so a nick in one knife shows up as a line across every board. A spiral head spreads the cut over many small blades; the WEN uses 26 staggered, rotatable HSS blades, so you can rotate a chipped one instead of replacing a whole knife. Reversible knives also save money: the CRAFTSMAN CMEW320 uses double-edged, reversible high carbon steel knives.

Snipe is a slightly deeper cut at the ends of a board, and it wastes length on every piece. Good table support helps, and the DW734 gives 33-1/2 inches of it.

Finally, check for a dust port and overload protection. Built-in overload protection cuts power during extreme loads to protect the motor.

Planers are loud and throw chips, so wear hearing and eye protection every time you run one. Keep your hands clear of the infeed and connect dust collection before you start; a planer’s chip flow clogs fast without it.

Common benchtop planer questions

What is snipe, and how do you reduce it?

Snipe is a slightly deeper cut at the start or end of a board, where only one feed roller is holding the wood and it can tip up into the cutterhead. You see it as a shallow dip a few inches from each end, which you then have to sand out or cut off.

The fix is keeping the board and the cutterhead from shifting. A carriage lock holds the head steady during the cut, and long infeed and outfeed tables support the board so its ends stay flat on the bed. Even so, buyers of planers sold with anti-snipe features still report some snipe at board ends, so plan to leave your boards a little long and trim the ends after planing.

Spiral or straight-knife cutterhead?

A spiral cutterhead uses many small blades set in a staggered pattern instead of two or three long knives across the head. The WEN PL1326, for example, has 26 staggered, rotatable HSS blades. Because each small blade can be turned to a fresh edge, a nick from a hidden nail means rotating one blade, not swapping a whole knife.

Straight-knife heads are simpler and use fewer, longer knives. The CRAFTSMAN CMEW320 uses double-edged, reversible knives, so when one edge dulls you flip it over before you need to buy new ones.

How much wood should you remove per pass?

Take light passes and let the machine’s gauge guide you. Several planers have an onboard material removal gauge that shows how deep each pass cuts, and the WOODERS planer has a height indicator reading 0 to 1/8 inch. Shallow passes are easier on the motor and on tricky grain, so take several thin cuts rather than one deep one.

Picking your planer

The DEWALT DW734 is the first pick if you want a fine finish with less snipe. Its three-knife head makes 96 cuts per inch, so hardwood boards come out smoother and need less sanding before glue-up or finish. The four-column carriage lock holds the cutterhead steady, which cuts down on the dips that ruin the last few inches of a board.

Before you buy, measure the widest board you plan to run. The DW734 takes boards up to 12-1/2 inches wide. If your tabletops or panels are wider than that, look at a 13-inch model so you are not ripping boards down to fit.