For most DIYers, the right Dremel rotary tool accessories kit is the one built around the materials you cut, sand and polish most, not the one with the biggest piece count. Dremel kits run from a tool bundled with a starter set, like the Dremel 4000 kit, to accessory-only sets such as the 108-piece All-Purpose Accessory Kit and the 160-piece 710-08 set. [1][2][3]
The 160-piece 710-08 includes cutting bits for carving and polishing, so it covers a wide spread of small jobs. [3] If you mostly shape wood, though, sanding drums and carving bits matter more to you than a drawer of cut-off wheels.
The 710-08 accessories have a 1/8″ shank and use EZ Lock Technology, so check that your rotary tool takes a 1/8″ shank before you buy an accessory-only set. [3]
What comes in popular Dremel accessory kits?
Popular Dremel kits come in three common sizes: a large accessory-only set, a mid-size all-purpose set and a bundle that pairs a tool with a smaller accessory selection. The piece count tells you how much variety you get. It says less about how long the kit will last on the jobs you do most.
The 160-piece 710-08 kit
The Dremel 160-Piece Rotary Tool Accessory Kit (710-08) is the large option, and it uses EZ Lock Technology with a 1/8″ shank [3]. Its accessories include cutting bits for carving and pieces for polishing [3]. This set suits you if you already own a rotary tool and want something on hand for most small jobs, from trimming a dowel to cleaning up a rusty hinge.
The 108-piece all-purpose kit
The Dremel Rotary Tool All-Purpose Accessory Kit (108-Piece) is the top-selling product in Home Depot’s Dremel rotary tool accessories category [2]. That popularity points to a middle ground many shoppers settle on. You get a broad mix of bits for general household and hobby work without paying for the larger set’s extra pieces.
The Dremel 4000 tool kit
The Dremel Kit 4000 comes with 39 pieces along with the tool itself [1]. It is meant for cutting, carving, engraving, polishing and sanding [1]. If you don’t own a rotary tool yet, a bundle like this gets you started with one purchase, and you can add accessories once you know which jobs you do most.
What a bigger count really adds
A higher piece count often comes from multiples of small consumables such as sanding bands and polishing pieces. A 160-piece set may have stacks of sanding bands and felt polishing pads but only a few of the specialty bits you’d reach for. Before you buy, count the items you’d use on your next three projects instead of comparing the total number on the box.
Will the accessories fit your rotary tool?
Most Dremel accessory kits will fit a standard Dremel rotary tool, because the bits use a 1/8″ shank. The 160-piece Dremel 710-08 kit, for example, is listed as a rotary tool accessories kit with a 1/8″ shank. [3] The shank is the smooth metal post at the base of each bit that the tool’s collet grips, so a 1/8″ shank needs a 1/8″ collet.
EZ Lock makes wheel changes faster
EZ Lock is Dremel’s quick-change system for cut-off wheels, and the 710-08 kit includes it. [3] On a standard mandrel you unscrew a tiny screw every time you swap a wheel, which gets fiddly when a thin wheel snaps mid-job. With an EZ Lock mandrel you pull back the head, slip the new wheel on and let it snap into place. If you cut a lot of bolts or thin metal, this saves real time and frustration.
Mixing brands takes a quick collet match
The collet is the small split sleeve inside the nose of the tool that tightens around the shank. Before you put bits from another brand into a Dremel, or Dremel bits into another brand’s tool, compare the shank size on the bit packaging with the collet in your tool. A bit with a shank that doesn’t match won’t tighten securely, and a loose bit can wobble or slip at high speed.
Some tools come with more than one collet size, so look at which one is installed before you swap bits.
Cordless models use the same accessories
Cordless Dremels take the same types of accessories as corded ones. The Dremel 8240 is a 12V cordless rotary tool, and one kit version, the 8240-5, comes with a 2Ah battery, charger, case and 5 accessory pieces. [4] Since only five pieces come in the box, a separate accessory kit is how you fill it out with sanding, cutting and polishing bits.
Which bits matter for woodworking?
For woodworking, the bits that earn their place in a kit are carving and engraving bits for detail, sanding drums and bands for shaping, and cutting wheels for thin pieces. Dremel kits are sold for exactly this mix of jobs: cutting, carving, engraving, polishing and sanding [1].
Carving and engraving bits for detail
Carving bits let you remove wood in small, controlled amounts. Use them to deepen the lines on a carved sign, clean out the corners of a recessed letter, or add texture to a decoy or spoon handle. The 160-piece 710-08 kit lists cutting bits for carving among its contents [3].
Engraving bits have finer tips. They work well for writing a name on a cutting board or adding small marks to a project. Let the bit’s speed do the work and make several light passes.
Sanding drums and bands for shaping
Sanding drums are small rubber cylinders. You slide a sanding band over the drum, which lets you shape curves that a flat sanding block can’t reach. Examples include the inside of a scroll-cut opening, the edge of a curved shelf bracket, or a rounded toy part.
Start with a coarse band to remove material, then move to a finer band to smooth it. Replace the band once it stops cutting cleanly or starts to burn the wood.
Cutting wheels for thin stock and small trims
Cutting wheels handle thin material and small trimming jobs. They work for cutting a dowel flush, notching a thin strip of trim, or trimming a craft plywood piece. For thick boards, use a saw.
Safety when cutting
Wear eye protection every time you use a cutting wheel, because a thin wheel can break and throw pieces. Clamp the workpiece to your bench or hold it in a vise so both hands stay on the tool. Never hold a small part in your fingers while you cut it.
What do you need for metal and hobby work?
For metal and hobby work, the four accessory types that earn their place are cut-off wheels, grinding stones, polishing wheels with compound, and engraving bits. Most all-purpose kits include some of each, so you can try a job before buying more of one type.
Cut-off wheels for bolts and thin metal
Thin abrasive cut-off wheels slice through rusted bolts, threaded rod, small screws and sheet metal. Picture a seized bolt on a trailer hitch or a screw that sticks out past a nut. You can trim either flush without pulling out a hacksaw.
Let the wheel do the cutting and use light pressure. These wheels are thin and brittle, and pushing hard snaps them.
Grinding stones for sharpening and deburring
Grinding stones are small shaped abrasive heads. Use them to touch up a lawn mower blade, a garden tool edge or a chisel. They also clean up the sharp burr left on metal after a cut.
The shapes do different jobs. A cylinder handles flat edges, and a pointed or ball shape gets inside holes and tight curves.
Polishing wheels and compound for finishing
Polishing kits pair felt or cloth wheels with a polishing compound. You rub the compound onto the spinning wheel, then buff the part. This brings back shine on chrome trim, brass hardware, jewelry and tarnished silverware.
Keep a separate wheel for each grade of compound. That stops coarse grit from scratching a part you are trying to finish.
Engraving for crafts
Engraving bits are fine-tipped cutters for adding names, dates or patterns to metal tags, glass, wood and stone. Large kits sell the same accessory set for carving, polishing and other detail work [3]. The Dremel 4000 kit is pitched for engraving along with cutting, carving, polishing and sanding [1].
Practice on scrap first. A light, steady hand and slow strokes give cleaner lines than speed does.
Where do accessory kits fall short?
Accessory kits are strong on variety and weak on depth: you get a little of everything, but rarely enough of the pieces that wear out fastest. Knowing where the gaps are helps you plan a few small add-on purchases instead of being stuck mid-project.
Wear-heavy pieces run out first
Cut-off wheels are the classic example. A kit might include a handful, and thin abrasive wheels can chip or snap when you cut a rusty bolt or a length of threaded rod. If you plan to trim several bolts or cut metal strapping, you can use up the kit’s supply in one afternoon.
Sanding bands and polishing pieces wear down too, though more slowly. Grinding stones lose their shape as you use them, so a stone that started out pointed for deburring will round off over time.
Attachments usually cost extra
Attachments are a separate category from bits and discs: they hold or guide the tool instead of doing the cutting. Dremel lists them alongside its bits as their own product group [5]. Accessory kits focus on the bits, so expect to buy a guide or holder on its own if your project needs one. Straight cuts in thin plywood and steady depth for routing are two jobs where a guide helps.
Buy refills of what you actually use
After a few projects, look at which compartments in the kit case are empty. Restock those pieces individually or in small packs, and skip pieces you never reach for. A woodworker might go through sanding drums and carving bits, while someone fixing hardware burns through cut-off wheels.
Other brands are an option
Dremel isn’t the only rotary tool you can pair with accessories. Ryobi and HART sell their own rotary tools, and either one may suit you if you already own batteries from that brand’s lineup. Weigh the tool itself, beyond the accessory count, before you settle on a brand.
Common questions about Dremel kits
Is a tool-plus-accessory kit better value?
If you don’t own a rotary tool yet, a bundled kit is usually the easier buy because you get the tool, a case and a starter set of bits in one box. The Dremel 4000 kit comes with 39 pieces and handles cutting, carving, engraving, polishing and sanding [1]. That covers most first projects, like trimming a dowel, smoothing a rough edge or etching a name into a tool handle.
Cordless bundles work the same way. One listing for the Dremel 8240-5 12V Cordless Rotary Tool Kit includes a 2Ah battery, charger, case and 5 pieces for US $64.99 [4]. A 5-piece starter set runs out quickly, so expect to add a separate accessory kit if you pick a bundle like that.
If you already own a Dremel, skip the bundles and put your money toward accessories.
Do bigger kits mean better quality?
A higher piece count gives you more pieces, and the bits themselves aren’t any better. A 39-piece set and a much larger set can hold the same types of bits. The large one simply has more of them.
Judge a kit by whether it holds the bits for your materials. If you mostly carve softwood, a smaller set with a good range of carving bits and sanding drums will serve you better than a big box built around polishing points you’ll never use.
Can you buy Dremel accessories singly?
Yes. Dremel sells bits and attachments as their own product category, so you can buy one type at a time [5]. This is the cheapest way to restock the pieces you wear out fastest, or to add a single specialty bit, like an engraving cutter for a craft project, without buying another full kit.
Picking your kit
Start with a mid-size all-purpose kit, then fill the gaps with single bits as your projects show you what you use. The 108-piece Dremel Rotary Tool All-Purpose Accessory Kit is a sensible first buy because it is the top seller among Dremel rotary tool accessories at Home Depot. [2] A kit that size gives you enough cutting, sanding and polishing pieces to learn which ones you reach for.
After a few projects, buy individual bits for your main material. If you carve wood most weekends, add extra carving bits and sanding bands. If you cut bolts, stock up on cut-off wheels. Prices shift often, so compare the current kit and refill prices before you check out.
