The Diablo Steel Demon carbide thin metal blade is worth buying if you cut thin metal often, since its carbide teeth are made to outlast standard blades by a wide margin. If you only cut a piece of conduit once in a while, a cheaper blade will likely do the job.
Diablo built this blade for extreme thin metal cutting, the kind of work where ordinary teeth dull fast. [1] The company claims up to 50X longer cutting life in thin metals compared with bi-metal blades. [2] For you, that means fewer blade swaps in the middle of a job, which counts most when you cut every day.
Below, you’ll find what the blade cuts, which sizes exist, how it stacks up on cost, where it falls short, and who should add one to their kit.
What materials is this blade made to cut
This blade is built for thin-walled metal: electrical conduit, metal tubing and similar light-gauge stock. Diablo describes its Steel Demon carbide reciprocating blades as the first designed for extreme thin metal cutting [1]. If most of your metal cuts are through pipe walls and sheet-thin material, this is the version made for that job.
Conduit and tubing are the main targets
The thin metal model is the industry’s first carbide-tooth blade for thin metal conduit and tubing [3]. In practice, that covers the cuts electricians and HVAC installers make all day: trimming EMT conduit to length, cutting out a section of old metal tubing, or slicing through light-gauge pipe during a remodel.
Thin walls are tricky for a reciprocating saw. With a coarse blade, only one or two teeth touch the metal at a time. The teeth can snag on the wall, the saw jumps, and the edge comes out ragged. A blade tuned for thin metal keeps more teeth in contact, so the cut stays smoother and the saw is easier to control.
Why carbide teeth matter on thin metal
Most metal-cutting reciprocating blades use bi-metal teeth, which are hardened steel welded to a flexible steel body. Carbide is a much harder material, so the teeth hold their edge longer when they rub against steel. Diablo built the Steel Demon line around carbide for that reason, and the thin metal blade brings it to conduit and tubing [3].
For you, that means fewer blade changes in the middle of a job. Picture cutting a dozen lengths of conduit for a basement circuit. On a blade that dulls quickly, the last few cuts get slower and rougher.
Thin metal version versus thick metal version
The Steel Demon family includes more than one blade, and each is matched to a material thickness. The thin metal version is tuned for light walls and tubing [1]. A separate thick metal version handles heavier stock such as angle iron, thick plate and solid bar.
Before you buy, picture the thickest metal you’ll cut on the project. Pick the thin metal blade for conduit runs, ductwork supports or a metal shelving frame. If you’re cutting heavy brackets or structural steel, choose the thick metal version.

Which sizes and tooth counts are available
The thin metal Steel Demon line comes in a few model numbers, and the two that matter most are blade length and tooth count. Below is what each listed model is and how to pick between them.
The models at a glance
|
Model |
Length |
Teeth per inch (TPI) |
Listed for |
|---|---|---|---|
|
DS0620CF |
Not listed |
Not listed |
Thin metal |
|
DS0612CF |
6 in. |
Not listed |
Thin metal conduit and tubing |
|
DS0820CF |
8 in. |
20 TPI |
Thin metal |
DS0620CF
The DS0620CF is Diablo’s thin metal carbide reciprocating blade, part of the Steel Demon family built for extreme thin metal cutting. [1] It is the model to look up first if you want the standard thin metal version, then match its length to your cuts.
DS0612CF for conduit
The DS0612CF is a 6 in. Steel Demon carbide blade aimed at thin metal conduit and tubing. [3] A 6 in. blade suits work in tight spaces, like cutting a run of EMT inside a stud bay or trimming tubing near a wall. The shorter length also flexes less on small-diameter pipe.
DS0820CF: 8 in., 20 TPI
The DS0820CF is an 8 in. blade with 20 TPI, sold for thin metal. [2] The extra 2 inches give you reach for wider stock, such as sheet metal ductwork, a bundle of tubing, or a cut where the saw body has to stay clear of the work.
Why higher TPI fits thin walls
TPI is how many teeth sit along each inch of the blade. More teeth mean smaller teeth spaced closer together, so several are always touching a thin wall at once.
That matters on conduit, tubing, and sheet metal. With too few teeth, a single tooth can catch the thin edge, which makes the blade grab, chatter, or tear the metal. A fine-tooth blade like a 20 TPI model takes small, steady bites and leaves a cleaner cut.
The tradeoff is speed in thicker material. Fine teeth fill with chips faster, so a high-TPI blade is the right choice when the metal is thin.

How does carbide compare with a bi-metal blade
A carbide blade costs more up front than a bi-metal blade, but it can outlast it by a wide margin, so the real comparison is cost per cut. Diablo’s carbide teeth give you up to 50 times the life of a standard bi-metal blade [4]. In practice, one Steel Demon thin metal blade could replace a whole stack of bi-metal blades if you cut metal often.
What you pay for bi-metal
Quality 18 TPI bi-metal blades run $3 to $4 each [4]. That low price is why most people keep a few in the truck or toolbox. They are easy to replace when the teeth dull, and losing one to a bind or a bent blade doesn’t sting much.
The catch is that dull bi-metal blades get swapped often when you cut a lot of conduit, tubing or sheet metal. Each swap means stopping work, and a dulling blade cuts slower and heats up the metal before you notice it’s time to change.
How the math works out
To compare the two, multiply the bi-metal price by the number of blades the carbide blade could replace. Take the 50x figure at face value: 50 bi-metal blades at $3 to $4 each comes to $150 to $200 worth of blades [4]. A carbide blade that costs several times more than one bi-metal blade still comes out ahead if you get anywhere near that life.
The “up to” matters. Your results depend on the material, your saw speed and how much pressure you put on the blade.
When bi-metal still makes sense
The savings only show up if you make enough cuts to use the extra life.
Bi-metal is also the cheaper choice for jobs where you might ruin a blade quickly, such as cutting near hidden nails or in awkward spots where the blade could bind and snap.
Where does the thin metal version fall short
The thin metal Steel Demon is the wrong pick once your stock gets thick or your cut includes wood. For heavy steel, Diablo makes a separate thick metal Steel Demon with carbide teeth built for that job, so you match the blade to the material instead of pushing one blade past its range.
Thick metal needs the thick metal blade
The thin metal blade’s fine teeth are spaced for conduit and tubing walls. On heavy stock, those small gullets (the gaps between teeth) pack with chips, the cut slows, and the blade heats up. You get the most out of carbide when the tooth pattern fits the wall thickness.
Diablo sells a separate Steel Demon carbide-tipped blade labeled for thick metal. [5] That version claims 50X life over bi-metal blades in thick metal applications, so the long-life claim carries over when you switch to the right blade for heavier work. [5]
What the thick metal 3-pack is rated for
The Steel Demon 3-pack sold as DS0408CF3 is rated for metals from 3/16 in. to 9/16 in. thick. [6] In practice, that range covers jobs like cutting angle iron, thick-wall pipe, flat bar or a rusted trailer bracket, where a thin metal blade would struggle.
A simple way to sort your projects:
-
Electrical conduit, thin-wall tubing, sheet metal ducts and light gauge studs go to the thin metal blade.
-
Steel 3/16 in. thick or more, up to 9/16 in., goes to the thick metal 3-pack. [6]
-
Anything heavier than 9/16 in. falls outside that pack’s rating, so plan on a different cutting method.
Not a wood or demolition blade
The Steel Demon thin metal blade is a metal-cutting blade, so keep it out of lumber and general demo. Ripping through framing, plywood or a wall packed with mixed materials will clog fine teeth and waste a blade you paid extra for.
For teardown jobs where you hit studs, nails and the occasional pipe in one pass, reach for a blade sold for demolition or wood with nails. Save the carbide thin metal blade for clean cuts in conduit and tubing, where its tooth count and long life pay off.
Where can you buy it and in what packs
You can buy the Diablo Steel Demon carbide thin metal blade from major U.S. retailers, and it commonly comes as a single blade. Walmart lists the Diablo Steel Demon Carbide Thin Metal Reciprocating Saw Blade as a Single Pack [7]. That suits a carbide blade well: you are paying for one long-lasting blade, so a single is often all you need to start.
Buying online at Walmart
Walmart’s listing offers free shipping and free 30-day returns [7]. That return window helps if you order the wrong length or find the blade does not suit your saw or your cuts. Keep the packaging intact until you have confirmed the size, because an opened, used blade is harder to send back.
The Walmart listing describes the blade as heavy-duty construction for professional use [7]. If you are a homeowner cutting a few runs of conduit, that label tells you the blade is built for daily jobsite work and is likely more blade than an occasional project needs.
The 8 in. model at Home Depot
Home Depot carries the 8 in. 20 TPI version under model number DS0820CF [2]. Searching that model number is the fastest way to land on the exact blade, since Diablo sells several Steel Demon versions with similar names. The thin metal and thick metal lines look alike on a shelf, so the model number keeps you from grabbing the wrong one.
Home Depot’s listing shows a 4.0 rating from 3 reviews [2]. Three reviews is a very small sample, so treat that score as a rough signal rather than a verdict on how the blade performs.
Picking the right listing
A few habits make buying simpler:
-
Search by model number, such as DS0820CF, instead of the product name alone.
-
Match the blade length on the listing to the length your cut actually needs before you add it to your cart.
-
Compare the single-blade price across retailers, since the same blade can be listed at more than one store.
Prices for carbide blades shift with sales and stock, so check the current price on each retailer’s page before you buy.
Should you add one to your kit
Add the Steel Demon thin metal blade if you cut conduit, tubing or other thin metal often. Electricians running EMT, HVAC installers trimming duct supports and anyone doing regular metal work get the most from a carbide-tooth blade built for thin conduit and tubing, since the blade keeps cutting long after a bi-metal one would be swapped out [3].
If you only cut a pipe or two a year, a quality 18 TPI bi-metal blade is the cheaper, sensible choice [4]. Either way, pick a blade length that fits the job. A 6 in. blade is easier to control on conduit in tight boxes, and an 8 in. blade reaches through larger tubing or a bundle of pipe in one pass.
Sources
-
8 in. 20 TPI Steel Demon Carbide Teeth Reciprocating Saw Blade for Thin …
-
Diablo 6-in. Steel Demon Carbide Reciprocating Saw Blades for Thin Met
-
Diablo Steel Demon Carbide Thin Metal Reciprocating Saw Blade – PTR
-
Diablo Steel Demon Carbide Teeth Reciprocating Saw Blades – 3-Pack
-
Diablo Steel Demon Carbide Thin Metal Reciprocating Saw Blade
