Kreg Rip-Cut Circular Saw Guide Review: Who It Suits and Its Limits

The Kreg Rip-Cut turns a regular circular saw into an edge-guided ripping tool for sheet goods up to 24 inches wide. Here is what it does well, where it falls short, and what to buy instead for wider or longer cuts.

A blue Kreg edge guide with a metal rail clamped to a red Ryobi circular saw, cutting a plywood panel over gravel.
In this article

Yes, the Kreg Rip-Cut is worth buying if you need straight rips in sheet goods and already own a circular saw. Its limit is width: it handles rips up to 24 inches, so it suits narrower parts more than full-sheet cuts.

The Rip-Cut turns an ordinary circular saw into an edge-guided cutting tool, so you get cleaner rips without a table saw. [1] It makes straight, repeatable cuts up to 24 inches wide in plywood, MDF and similar panels. [1] That makes it a good fit for breaking down a 4 x 8 sheet into shelves or cabinet parts in your garage or driveway.

This review covers how it keeps the cut straight, which saws it fits, what buyers like and dislike, and when a longer guide or track saw makes more sense.

How does the Rip-Cut keep your cut straight

The Rip-Cut keeps your cut straight by guiding the saw off the sheet’s own edge instead of a line you draw. It uses an oversized edge guide that rides the edge of your sheet, so the saw stays aligned from start to finish [2]. You set the width once, then push the saw forward while the guide slides along the panel.

The edge does the steering

Think of it like a rip fence on a table saw, turned around. On a table saw the fence is fixed and the board moves; with the Rip-Cut the board stays put and the fence travels with your saw. The guide’s long face presses against the factory edge of the plywood, which keeps the blade from drifting off line as you walk the cut.

That is why the guide is oversized. A longer bearing surface against the edge is harder to twist, so a small wobble in your hands at the start of the cut doesn’t turn into a wavy line halfway down a 4-by-8 sheet.

No pencil lines for each rip

Because the width comes from the guide setting, you don’t need to draw lines for each cut [2]. Say you need six shelf blanks at 11 1/4 inches. You set the guide once, make the first rip, slide the next section into place and cut again. Every piece comes off at the same width, and you skip measuring and marking at each end of the sheet.

This also saves you from small marking errors. A pencil line that’s off by 1/16 inch at one end gives you a tapered part, while a fixed guide setting gives the same width along the full length.

Your reference edge sets the accuracy

The guide copies whatever edge it rides on, flaws included. A clean factory edge on new plywood or MDF gives you a straight cut. A dinged, swollen or previously hand-cut edge passes its bumps and curves straight into your new cut.

If the edge you have isn’t trustworthy, make your first cut a cleanup pass along a known-straight edge, then use that fresh edge as the reference for the rips that follow. Keep the guide pressed firmly against the edge through the whole pass, because any gap that opens up shows up as a dip in your cut.

Close view of a saw guide's fence riding along a plywood edge as the circular saw blade makes a clean, straight rip cut.

Will it fit your circular saw

The Rip-Cut is designed around a standard circular saw with the blade on the side of the motor, so that is the saw it suits best. Kreg’s Amazon listing says the guide works best with a regular (side-blade) circular saw. [3] If that is what hangs in your garage, the most common type sold for DIY use, you are the buyer this guide was built for.

Side-blade saws

A side-blade saw (sometimes called a sidewinder) has the motor in line with the blade and the handle on top. Most budget and mid-range corded and cordless circular saws you see at hardware stores follow this layout. With one of these, the saw base mounts to the Rip-Cut’s sled and the edge guide keeps the blade parallel to the sheet’s edge.

An easy way to tell what you own: look down at the saw from the handle. If the motor sits beside the blade and the handle is roughly above the motor, you have a side-blade saw.

Worm-drive and rear-handle saws

Worm-drive and rear-handle saws are a different story. These saws put the motor behind the blade and use a long body with the handle at the back, which changes the base shape and where the blade sits relative to the shoe. Because the guide is listed as working best with side-blade saws, a worm-drive or rear-handle saw may not sit on the sled the way it is meant to. [3]

If you own one of these, measure your saw’s base plate and the distance from the blade to the edge of the shoe before you order. Bring the saw to the store if you buy in person, and try it on a display unit. Buying a cheap side-blade saw just for sheet-goods work is another route some owners of worm-drive saws take.

Two model numbers, same tool family

You will see two model numbers when you shop. Home Depot lists the 24-inch Rip-Cut aluminum circular saw guide as KMA2400, which is also the model in the URL of Kreg’s own store page. [1] [2] Amazon lists the Rip-Cut as KMA2685. [3]

When you compare prices, match the model number on each listing so you know exactly which package you are getting.

Hands tighten clamps to secure a circular saw's flat base plate onto a sliding guide sled resting on a wooden workbench.

How wide can you rip, and on what materials

The Rip-Cut makes straight, accurate, repeatable cuts up to 24 inches wide in plywood, MDF and other sheet goods. [1] That 24-inch figure is measured from the edge the guide rides on, so any strip you can mark at 24 inches or less from a factory edge is within reach. A 2-foot-deep cabinet side fits. A 30-inch-wide panel does not.

What 24 inches covers in practice

Most home shop rips fall inside that range. Here are typical parts you can cut from a 4×8 sheet:

  • Base cabinet sides around 23 inches deep

  • Bookshelf sides and shelves at 11 or 12 inches

  • Drawer box sides at 4 to 6 inches

  • Narrow cleats, nailers and face-frame blanks at 2 to 3 inches

A 48-inch-wide sheet ripped down the middle gives two 24-inch halves. That puts a center rip right at the tool’s maximum, so you can split a full sheet into two manageable pieces before cutting the parts.

Sheet goods are the sweet spot

Plywood, MDF and similar panels are the materials the guide is built for. [1] They come with long, straight factory edges for the guide to follow. They are also hard to push through a table saw alone, which is why a guide on a circular saw works well in a garage or driveway. Solid lumber with a crooked or rounded edge gives the guide nothing straight to follow, so it is a poorer fit.

Repeatability is the real payoff

Because you set the width once and lock it, every rip after the first comes out the same. If you need four 11-1/4-inch shelves for a bookcase, you set the guide at 11-1/4 inches and make four passes. The shelves match, and that matching matters more than hitting an exact number: two cabinet sides that are identical will sit square even if both are a hair off your plan.

When the cut is wider than 24 inches

Past 24 inches you need another method. One option is a long clamp-on straight edge you position by measuring at both ends. Another is a dedicated rail or track system. The Rip-Cut can’t stretch to cover these cuts, so plan your cut list with that limit in mind.

What buyers like and what they complain about

Buyers mostly praise the Rip-Cut for speed on repeat rips, and the main complaint is how narrow its job is. Its guide rides the edge of the sheet, so you can set a width once and cut strip after strip without drawing lines [2]. That same design means it only cuts parallel to an existing edge.

What works well

Repeat rips go quickly. If you need six 11 1/4-inch shelf strips from a sheet of plywood, you lock the width, run the saw, slide the guide to the fresh edge and cut again. You skip measuring and marking each piece, which is where small errors usually creep in.

The guide also holds the saw on line through the whole pass [2]. For a beginner, that removes the wandering cut that makes freehand circular saw rips frustrating.

Where it falls short

The Rip-Cut is edge-referenced. It needs a straight edge to ride against, and it can only cut parallel to that edge. That rules out these jobs:

  • Tapers and angled cuts across a panel

  • Cuts on a board with a rough or crooked edge, since the cut copies the edge

  • Crosscuts on a full sheet, where the guide has no nearby edge in range

Ratings at two retailers

Owner ratings differ a lot depending on where you look.

Retailer

Average rating

Number of ratings

Kreg official store

4.4 [2]

896 [2]

Home Depot

3.4 [1]

56 [1]

The Kreg store score rests on far more ratings, so it reflects a broader group of owners. The Home Depot score is a full point lower but comes from a much smaller sample, where a handful of unhappy buyers moves the average more. Read the low reviews at both stores to see whether the complaints match how you plan to use it. If they mention angled cuts or wide panels, those are jobs the tool was never built for, and they may not apply to you.

When a straight edge guide or track saw is the better buy

A long straight edge guide is the better buy when your cuts run the full length of a sheet or across it at an angle. A track saw is the better buy when you cut sheet goods often enough to justify a dedicated system. The Rip-Cut stays the right choice when you rip occasionally and want to keep spending low.

Long guides for full-length and angled cuts

The Kreg 96″ Straight Edge Guide makes straight cuts up to 8 feet in sheet goods. That covers the full 8-foot length of a standard plywood or MDF sheet, so you can trim a sheet lengthwise or square up a rough end in one pass. [4]

A long guide clamps onto the panel wherever you place it, so the cut doesn’t have to run parallel to an edge. That makes it the tool for crosscutting a 4-foot sheet in half, cutting a tapered panel, or making an angled cut for a sloped shelf. The Rip-Cut can’t do these because its guide rides the sheet’s edge, which keeps your saw aligned only along that edge. [2]

When a track saw makes sense

A track saw pairs a plunge saw with its own rail, so the saw and guide work as one system. Consider one if you break down plywood every week for cabinets or built-ins and want setup to be quick and repeatable. If you cut a few sheets a year, the circular saw you already own plus a guide does the same job for far less.

Side-by-side comparison

Option

Best for

Cut direction

Uses your existing circular saw

Kreg Rip-Cut

Occasional rips on a budget

Parallel to the sheet edge

Yes

Kreg 96″ Straight Edge Guide

Cuts up to 8 feet, crosscuts, angled cuts

Anywhere you clamp it

Yes

Track saw

Frequent sheet-goods work

Anywhere you place the rail

No, dedicated saw

The Rip-Cut is quickest for repeat rips but is tied to the sheet’s edge. The straight edge guide trades some setup time for freedom over length and angle. A track saw costs the most but gives you a complete system if sheet goods are a regular part of your work.

Which Kreg guide should you pick

Pick the Rip-Cut if most of your cuts are rips under 24 inches, and pick the straight edge guide if you need long cuts across a full sheet. For example, ripping a stack of 16-inch shelf parts from plywood is Rip-Cut work. Cutting a 4×8 panel down its full length, or slicing it at an angle, calls for the Kreg 96-inch Straight Edge Guide, which handles straight cuts up to 8 feet in sheet goods. [4]

Before you order, look at your saw. The Rip-Cut works best with a regular side-blade circular saw, so a worm-drive or rear-handle model may not be a good match. [3] Then check the current price on Kreg’s official page and buy the guide that fits the cuts you make most.

Sources

  1. Kreg 24 in. Rip-Cut Aluminum Circular Saw Guide KMA2400

  2. Kreg Rip-Cut™ Circular Saw Guide | KregTool.com Official Store

  3. Kreg Rip-Cut Circular Saw Guide, Cuts up to 24″ Wide, KMA2685

  4. Kreg® 96″ Straight Edge Guide