Kreg Drilling Guide KDG-6000: What It Does and Who Should Buy It

The Kreg KDG-6000 is a handheld jig with six hardened steel guides that keeps your drill bit straight and on your mark. Here is what it handles well, where it falls short and who gets the most from it.

A hand holds a blue Kreg drilling jig on the edge of a wooden board while a drill bit bores through one of its guide holes.
In this article

The Kreg KDG-6000 is worth it if you drill with a hand drill and want straight holes without buying a drill press. Kreg makes it as a portable jig that helps you create straight holes without a drill press. [1] If you already own a drill press, it adds less, since that machine already keeps your bit square.

The kit comes with six hardened steel drill guides, from 1/8 in to 1/2 in, that hold your drill in position for you. [2] That range covers common jobs like pilot holes for screws, holes for shelf pins and through-holes for bolts, with only a hand drill. [3]

Below you’ll find what the guide does, how you use it, which projects it suits, where it falls short and whether you should buy one.

What does the KDG-6000 actually do

The KDG-6000 does one job: it keeps a handheld drill pointed straight at the spot you marked. You set the guide on the workpiece, put your bit through one of its steel guide holes, and the guide holds the drill in position so you don’t have to rely on a steady wrist and a good eye.

The guides hold the drill for you

The steel guides do the work of holding your drill in position for you. [2] Without a guide, a hand drill tends to tilt a few degrees as you push, and the hole comes out angled. That matters when a shelf pin, dowel or bolt has to sit square in the board.

With the guide in place, the bit runs through a fixed hole instead of floating free. Say you’re drilling holes for a towel bar bracket in a cabinet side. The guide keeps the bit square to the panel, so the bracket screws line up with the holes on the other side.

Alignment marks put the hole where you want it

The guide has built-in hole alignment marks that help you place each hole on your layout. [4] You draw your crosshairs on the wood, line the marks on the guide up with those lines, and the guide hole lands over your mark.

This saves you from guessing where the center of a hole will fall once the guide is sitting on top of your pencil line. It helps most when you’re drilling a row of holes that have to match, such as dowel holes on two mating boards.

GripMaxx keeps it from sliding

The guide uses Kreg GripMaxx material that keeps it in place as you work, so your drill bit won’t wander off your mark. [5] A smooth plastic base can skate across a finished or slick surface the moment the bit starts spinning, and that’s when a hole drifts a quarter inch from where you wanted it.

The grippy base helps most on smooth stock like melamine shelving, prefinished plywood or planed hardwood. You still press down with your free hand, but the guide stays put while the bit bites into the wood.

A woodworker's hands guide a cordless drill through a drill guide, boring a straight vertical hole into a pine board.

Sizes, materials and dimensions

The KDG-6000 comes with six steel drill guides that cover bit sizes from 1/8 in to 1/2 in, all held in one compact body you grip by hand. [2] In practice, one tool covers small pilot holes for screws on up to larger holes for dowels, bolts or cable runs, so you don’t need a separate jig for each bit.

Guide sizes

The six guides run from 1/8 in at the small end to 1/2 in at the large end. [4] A 1/8 in guide suits pilot holes for small screws in trim or hardware. A 1/2 in guide handles a hole for a carriage bolt or a 1/2 in dowel.

You match the guide to the bit you’re using. The bit should slide through the guide without slop, and that close fit is what keeps the hole straight.

What the guides are made of

The guides are hardened, heat-treated steel. [6] Heat treating makes the steel harder, so a spinning drill bit is less likely to wear the guide hole oversize over time.

This is important because a worn guide lets the bit wander, which defeats the purpose of using a guide at all. A soft plastic or aluminum guide would wear faster, especially with steel bits running at drill speed.

Size and shape

The guide measures about 6.97 in long by 2.48 in wide. [6] That’s roughly the length of a smartphone and a little narrower, so it fits easily in a tool bag or a drawer next to your drill.

The small footprint also helps on narrow stock. A 2.48 in width means you can set the guide on the edge of a 2×4 (actually 3-1/2 in wide) or on a cabinet face frame without it hanging far off the sides.

Ergonomic hand-held body

The body has an ergonomic design, meaning it’s shaped to sit in your hand while you drill. [2] You hold the guide against the work with one hand and run the drill with the other, rather than clamping a fixture to a bench.

That hand-held shape is what lets you take the guide to the workpiece, whether it’s a long board on sawhorses or a shelf already on the wall.

A metal drill guide lies beside a tape measure and assorted drill bits on a wooden workbench in a home workshop.

How you use it on a project

Using the KDG-6000 comes down to four moves: mark your hole, line the guide up on the mark, choose the steel guide that matches your bit, and drill while you hold the jig steady. Each step takes only a few seconds once you’ve done it a couple of times.

  1. Mark the hole center on your workpiece with a sharp pencil or an awl. A small cross works better than a dot, because its two lines give you something to line up against. If you’re drilling shelf-pin holes in a cabinet side, for example, mark every hole location before you pick up the drill.

  2. Set the guide on the workpiece and line up its built-in hole alignment marks with your pencil lines. Getting this right is what puts the hole where you want it, so take a second look from directly above before you drill.

  3. Pick the steel guide that matches your drill bit. The set runs from 1/8 in to 1/2 in, so a 1/4 in bit goes in the 1/4 in guide [4]. A snug fit matters: if you use a guide that’s larger than the bit, the bit can wobble and the hole won’t come out straight.

  4. Press the guide down firmly with your free hand and drill through the steel guide. The guide holds the drill in position for you, so you can focus on steady pressure instead of eyeballing the angle [2]. The GripMaxx material on the base helps keep the jig from sliding, which stops the bit from wandering off your mark [5].

  5. Lift the drill straight back out of the guide before you move the jig to the next mark. If you pull at an angle, you can widen the top of the hole.

Staying safe while you drill

Keep the fingers of your holding hand on the body of the guide and away from the bit’s exit point. When the bit breaks through the back of the board, it can catch anything underneath it, including your hand or the edge of a workbench.

Clamp small or narrow workpieces to your bench before you drill. A short piece of trim can spin if the bit grabs, and you can’t hold the part and the guide steady at the same time with one hand. Put a scrap board underneath as a backer so the bit exits into waste wood instead of your benchtop.

Which projects suit this drill guide

The KDG-6000 fits best on jobs where you can’t bring the wood to a drill press, or where you need the same straight hole many times. Kreg describes it as a portable guide for creating straight holes without a drill press [1]. That makes it most useful in three kinds of work.

Pieces too big or already installed

Some work won’t fit on a drill press table, and some is already screwed to a wall. You can’t slide an 8-foot bookcase side, a closet shelf or a mounted cabinet face frame under a drill press spindle. With this guide you bring the straight-hole setup to the wood instead.

This works well for a few common jobs:

  • Drilling a hole through an installed cabinet back to run a cable or pipe

  • Adding a hole for a hinge pin or bolt on a door that’s already hung

  • Boring a hole for a handle in a long tabletop apron

  • Drilling into a built-in bench or window seat after assembly

You get precisely positioned holes with just a hand drill [3]. On a fixed piece, that’s the difference between a hole that runs square and one that wanders off at an angle.

Repeated holes in furniture and cabinets

Furniture and cabinet builds often call for the same hole over and over. A row of shelf-pin holes, matching dowel holes on both sides of a joint, or bolt holes for bed rails all need to go in straight so the parts line up.

Drilling these freehand means each hole can tilt a little differently. A guide that keeps the bit straight helps the parts match when you assemble them. For a set of chairs or a run of kitchen cabinets, that consistency saves you from re-drilling or forcing pieces together.

Jobs away from the shop

The guide is a portable jig, so it travels in a tool bag with your drill [7]. That helps if you build on site, fix things at a friend’s house, or work in a garage with no room for stationary tools.

For example, if you’re installing a deck railing, mounting a workbench, or building shelving in a basement, you can drill straight holes right where the parts go.

Where the KDG-6000 falls short

The KDG-6000 has limits, and they come from what it is: a handheld block of steel guides. Before you buy, it helps to know the jobs it won’t handle well so you can plan around them.

The largest hole is 1/2 inch

The biggest guide in the set is 1/2 in, so that is the widest straight hole the jig can steer. [2] If your project calls for a 5/8 in dowel, a 3/4 in hole for running a cord through a desk, or a 1 in hole for a closet rod bracket, the KDG-6000 can’t help with that hole.

For those sizes you need a different tool, such as a spade bit or Forstner bit chucked in a drill press, or a larger dedicated doweling jig. Plan your hardware around 1/2 in or smaller if you want this guide to do all the drilling on a build.

It drills straight holes, and you set the depth

The guides hold your drill in one position, square to the surface. [4] That is the whole job. You can’t tilt the jig to drill an angled hole, so pocket holes and splayed chair legs need another jig.

Depth is the other gap. The guide keeps the bit straight, but how deep the bit goes depends on how hard and how long you push the drill. Drilling 1 in deep for shelf pins on the left side of a cabinet and getting the same depth on the right side takes care on your part. A stop collar on the bit or a strip of tape wrapped around it as a depth mark helps, though neither is as consistent as the depth stop on a drill press.

It’s slower on big production runs

Each hole means placing the guide, lining it up, holding it and drilling. For a handful of holes that’s quick. For 200 shelf-pin holes across a set of kitchen cabinets, the setup on every hole adds up, and your hands tire.

A drill press with a fence and stop block lets you slide each part into place and drill the next hole in seconds. If you drill the same hole over and over in a shop, the press is faster and more repeatable. The KDG-6000 fits better when the holes are fewer or the work is too big to move.

Should you buy one

Buy the KDG-6000 if you drill with a hand drill and don’t own a drill press; if a drill press already sits in your shop, you can skip it. Buyers rate it well across major U.S. retailers: 4.4 out of 5 from 115 ratings at Home Depot [2], 4.6 from 139 ratings at Lowe’s [4], and 4.6 from 468 ratings at Acme Tools [3]. Those scores mean most owners got the straight, well-placed holes they bought it for.

Your next step is simple. Compare the current price at Home Depot, Lowe’s or Kreg before you order, since retailers often price the same set differently, then pick the store that fits your budget and shipping needs.

Sources

  1. Portable Drill Guide

  2. Kreg Drilling Guide KDG-6000

  3. Kreg Drilling Guide KDG-6000

  4. Kreg 6-Piece Drill Guide Set with Hardened Steel …

  5. Kreg Plastic Drill Guide 1 pc Mfr# KDG-6000

  6. Kreg Portable Drilling Guide

  7. Kreg KDG-6000 Drilling Guide