Lenox carbide tipped reciprocating saw blades are worth it when you cut hard material: cast iron, stainless steel, or wood full of hidden nails. For quick cuts in clean lumber or thin metal, the extra cost buys you little, and a standard blade does the job. Lenox sells its Carbide CT line for high performance in cast iron and stainless steel [1]. The carbide is welded to the cutting edge to help prevent tooth loss [2]. That matters on a demolition job, where one nail can strip teeth off a cheaper blade halfway through a cut.
If you remodel, replace old cast iron drain pipe, or tear out framing, the right blade saves you trips to the store mid-project. Below you’ll see what these blades cut, the sizes and tooth counts in the lineup, how they stack up against bimetal and Diablo blades, and how to make one last.
What can these blades cut
Lenox carbide tipped reciprocating saw blades are made for the hard jobs: tough metals, dirty demolition cuts and wood with hidden fasteners. If your project involves old plumbing, salvaged lumber or tree limbs, these blades are aimed at you.
Cast iron and stainless steel
The Lenox CT line is built for high performance in cast iron and stainless steel. [1] These are the metals that dull ordinary teeth fast, so they are where a carbide blade earns its place.
A common example is cutting out an old cast iron drain stack during a bathroom remodel. Another is trimming a stainless steel bracket, rail or sink flange when you are replacing fixtures. Both jobs involve thick, hard material that you would otherwise cut slowly with a grinder.
Demolition, pruning and thick metal
Lenox lists demolition, pruning and thick metal cutting as uses for its carbide tipped reciprocating blades. [3] That covers a wide range of work for a homeowner with one saw.
In demolition, you might cut through wall framing, old cabinets or a deck you are tearing out. For pruning, a reciprocating saw with a long blade can take down overgrown shrubs and lower branches without a chainsaw. Thick metal jobs include steel pipe, angle iron or heavy brackets on a shed or fence.
Nail-embedded wood
Lenox carbide tipped blades are also sold for fast cuts in wood with nails in it. [4] That matters most when you cannot see what is inside the board.
Think of cutting a wall plate that is nailed to the subfloor, or trimming reclaimed barn wood full of old nails. A standard wood blade can lose teeth the moment it hits steel, while a blade meant for nail-embedded wood keeps cutting through both.
A masonry version exists
Lenox also makes a separate carbide tipped masonry reciprocating blade, listed at 450 x 50 x 1.2 mm. [5] In inches, that is a blade roughly 17.7 inches long and about 2 inches tall.
Use this one, not the wood and metal blades, when you need to cut brick, block or similar masonry. The regular carbide line covers wood and metal; masonry calls for its own blade.

Which sizes and tooth counts are in the lineup
Lenox makes three carbide-tipped reciprocating blades, and each comes in 6-inch, 9-inch and 12-inch lengths. The medium metal blade also comes in a 4-inch length. [6] That gives you a short option for tight spots, like cutting a pipe between wall studs, and long options for reaching through thick stock.
Matching length to the job
The length you pick mostly depends on how much material you need to reach through. Here is how the sizes tend to fit common jobs:
The 4-inch medium metal blade suits cramped spaces where a longer blade would hit the wall behind the cut.
The 6-inch blades handle most pipe, conduit and bolt cutting where you have room to work.
The 9-inch blades give extra reach for framing lumber with nails, or larger metal pieces.
The 12-inch blades are for thick demolition cuts and big material.
Examples of tooth counts
Tooth count is listed as TPI (teeth per inch), and it changes with the blade’s intended material. The 6-inch heavy-duty blade has 8 TPI. [1] A 9-inch carbide-tipped version comes with 10 TPI and is sold in 2-packs. [4]
As a rule of thumb, fewer, larger teeth clear chips fast and suit wood and nail-embedded wood. More, finer teeth keep several teeth in contact with thin or hard metal, which gives a smoother, less grabby cut. So if most of your work is cutting steel pipe, lean toward the higher TPI blade, and for tearing out old framing, lean toward the lower one.
The 5-piece set
If you want to try several blades at once, Lenox sells a 5-piece set under part number LXARCT5SET. It includes blades 656RCT, 6108RCT, 6110RCT, 956RCT and 9108RCT. [2]
The set makes sense if you do mixed work, such as a bathroom remodel where you cut cast iron drain pipe one day and nailed studs the next. If you only cut one material, buying single blades or a 2-pack in the right length and TPI is usually the simpler choice. Write down the part number of the blade that works best for you so reordering is easy. Related reading: Who Makes the Best Bandsaw Blades? Brands Matched to Your Cuts.

Where carbide beats bimetal, and where it falls short
Carbide beats bimetal when the cut is hard on teeth, and bimetal still wins on price when the cut is easy. The deciding question is how often your blade will hit something that chips or strips ordinary teeth.
The life claim comes from the maker
Lenox advertises its carbide tipped blades as lasting up to 50X longer, and that figure carries an asterisk [2]. Treat it as a best-case number from the manufacturer, measured under conditions you won’t see on the package. In your own work, the real gain depends on what you cut and how you run the saw.
A fair way to read it: in tough material, expect one carbide blade to replace several bimetal blades. In soft, clean wood, the gap shrinks because a bimetal blade isn’t wearing out fast to begin with.
Harder teeth hold up to nails and tough metal
Carbide is much harder than the high-speed steel edge on a bimetal blade. Lenox welds carbide to the cutting edge to add durability and help prevent tooth loss [2]. That matters most when the blade hits something that knocks teeth off a standard blade.
These are the jobs where you’ll notice the difference:
Cutting through old framing where you can’t see every nail or screw
Slicing cast iron drain pipe during a bathroom remodel
Long cuts in thick or hard steel, where a bimetal blade dulls partway through
Repeated cuts in the same tough material, when stopping to swap blades costs you time
With bimetal, a hidden nail can strip a few teeth and leave the blade chattering. A carbide tooth is more likely to cut through and keep going.
Where carbide falls short
The main drawback is cost. A carbide tipped blade costs more per blade than a bimetal one, so it only pays off if you’d otherwise burn through several bimetal blades on the same job.
For light, clean work, bimetal is the sensible pick. Trimming a few 2x4s, cutting PVC, or making occasional cuts in thin sheet metal won’t stress a bimetal blade much. Paying extra for carbide there buys durability you won’t use. A practical setup for many homeowners is a carbide blade saved for demolition and metal, with cheaper bimetal blades for everyday cuts.
How do they compare with Diablo carbide blades
Lenox advertises its carbide tipped reciprocating saw blades as lasting up to 30% longer than Diablo blades, which is a useful hint but not proof that they will outlast a Diablo on your job. [3] That figure appears in the product listing, so it reads as the manufacturer’s own marketing claim. Nothing attached to it describes an independent, side-by-side test.
What the 30% claim tells you
If the claim held up in your shop, a Lenox blade would keep cutting for about one extra blade’s worth of work for every three Diablo blades you wear out. On a demolition job where you burn through several blades a day, that adds up to fewer blade changes and fewer trips to the store.
The listing also says these blades are meant for demolition, pruning and thick metal cutting. [3] Any comparison with Diablo only means something within that kind of work. A blade that lasts longer through cast iron pipe may not show the same edge when you’re trimming a tree limb.
Why to treat it as marketing
A “longer life” number depends on how it was measured. It matters what material was cut, how thick it was, which saw and stroke speed were used, how hard the operator pushed, and which Diablo blade was the comparison. None of those details come with the claim, so you can’t tell whether the test matches the way you work.
The phrase “up to” also matters. It describes the best result, not the typical one. In your hands the gap could be smaller, larger or reversed, depending on the cut.
How to compare them yourself
The fairest test is your own. Buy one Lenox and one Diablo carbide blade in the same length and tooth count, and use them on the same kind of cut. Cutting 2x4s with embedded nails or a stack of steel conduit works well for this.
Keep a simple tally of how many cuts each blade makes before it slows down noticeably or starts to wander. After a few jobs you’ll know which brand gives you more cuts per dollar on the work you do most. That tells you more than a headline percentage.
How to get the longest life from a carbide blade
A carbide blade lasts longest when it is long enough for the job and the saw does the cutting at its own pace. Most early failures come from a blade that is too short, or from leaning on and twisting the saw mid-cut.
Pick a length that reaches past the material
Choose a blade that extends past the far side of the workpiece through the whole stroke. If the tip stays buried inside the material, the same few teeth do all the work and the tip can catch and bend on the back stroke.
The carbide-tipped blades come in 6″, 9″ and 12″ lengths, and the medium metal blade also comes in a 4″ length. [6] For example, a 6″ blade suits a single 2×4 or a small pipe, while a 9″ blade gives you room to cut through a doubled stud wall with nails in it. Save the 12″ length for thick timbers or long reach cuts, since a longer blade flexes more on thin stock.
Let the saw work
Hold the shoe of the saw firmly against the material and apply light, steady pressure. Pushing hard heats the teeth and dulls them faster, even with carbide, and it rarely speeds up the cut.
Keep the blade in a straight line. Twisting or prying the saw to steer a cut puts side load on the blade, which is how blades bend or snap and how teeth chip.
A few habits help on tough cuts:
Start the cut at a lower speed until the blade has a groove, then increase speed.
Use orbital action for wood and nail-embedded lumber, and turn it off for metal.
Back the blade out and restart if it binds, instead of forcing it through.
Clamp or support the workpiece so it does not pinch the blade as it drops.
Safety for demolition cuts
Wear safety glasses and work gloves every time. Carbide cuts through nails and metal, so chips and hot fragments fly, and freshly cut edges are sharp.
Before cutting into a wall, floor or ceiling, check for hidden wires and pipes. Turn off power to the circuit and the water supply to that area, and make shallow plunge cuts so you can see what is behind the surface before cutting deeper.
Which blade should you buy first
If you do demolition or cut metal, buy a 9 inch carbide blade first, or get the 5-piece set if you want several lengths and tooth counts on hand. The 9 inch carbide-tipped blade has 10 TPI and comes in a 2-pack, which gives you a spare for a long tear-out job [4]. Its carbide is welded to the cutting edge, so it holds up in demanding metal cuts [2].
If you only trim the odd board or cut clean lumber now and then, a bimetal blade is enough, and you keep the money for the jobs that need carbide. Weighing blade makers for your bandsaw as well? The pillar article on bandsaw blade brands compares them side by side.
