Milwaukee Metal Cutting Circular Saw Blades: How to Choose

Milwaukee metal cutting blades come in sizes from 5-3/8 in to 14 in. Match the diameter to your saw and the tooth count to the metal you cut.

Milwaukee Metal Cutting Circular Saw Blades: How to Choose
In this article

Pick a Milwaukee metal cutting circular saw blade that matches your saw’s diameter first, then choose the tooth count and blade line that suit the metal you’re cutting. A blade that fits your saw but has the wrong teeth for the job will still cut slowly or leave a rough edge.

That matters because Milwaukee’s metal blades cover a wide spread of sizes, from 5-3/8 in up to 14 in [1]. Tooth counts vary too: the 8 in 48-40-4515 carries 42 teeth [2]. Milwaukee designs these blades for dry metal cutting, so you don’t need coolant on the job [2].

Below you’ll find the sizes Milwaukee makes, how many teeth suit steel of different thicknesses, and what the carbide is made of. Later sections cover cutting metal safely and whether these blades are worth the price.

What blade sizes does Milwaukee make for metal?

Milwaukee makes metal cutting circular saw blades in diameters from 5-3/8 in up to 14 in, so there is a size for most saws you are likely to own. [1] The right one is set by your saw: find the blade diameter stamped on the saw’s guard or printed in its manual, and buy that size.

Common sizes and where they fit

The sizes fall into a few practical groups. Here is how they line up with typical saws:

Blade diameter

Typical saw

Example

5-3/8 in

Compact metal cutting saws

48-40-4070

7 in

Mid-size circular saws

Milwaukee’s most reviewed metal blade on one major retailer’s listing

8 in

Full-size metal cutting saws

48-40-4515

Up to 14 in

Large saws for heavy stock

Varies by model

The 5-3/8 in blade is the smallest in the range. [1] Milwaukee sells it as part of the Metal & Stainless line under part number 48-40-4070. [3] If your saw is a compact model, such as a cordless saw built for trimming steel studs or conduit on a ladder, this is usually the size to look for.

The 7 in blade sits in the middle of the range and is the most reviewed Milwaukee metal blade at Home Depot. [1] That popularity reflects how many mid-size saws take this diameter.

For an 8 in saw, the 48-40-4515 is a good example. It is an 8 in blade from the Metal & Stainless Cutting line. [2]

Match the size exactly

Never fit a blade bigger than the size your saw is rated for. A larger blade won’t fit under the guard properly, and the saw’s speed and arbor are matched to its rated diameter. A smaller blade may mount, but it shortens your cutting depth, so a 7 in saw works best with a 7 in blade.

Three metal cutting circular saw blades of different diameters are laid side by side on a wooden workshop table.

How many teeth do you need for steel?

Tooth count is one of the easiest ways to tell Milwaukee’s metal blades apart, and the two common sizes carry different counts. The 7 in blade has 54 carbide teeth, while the 8 in 48-40-4515 has 42 teeth. [1] [2]

What the two counts look like

Blade

Diameter

Teeth

Milwaukee 7 in metal blade

7 in

54 carbide teeth

Milwaukee 48-40-4515

8 in

42 teeth

[1] [2]

The 7 in blade is the most reviewed Milwaukee metal circular saw blade in its category, so many DIYers start with it. [1] Since you can’t swap diameters on a saw, the size your saw takes usually decides which tooth count you get.

Match teeth to the thickness of the metal

Think about how many teeth sit in the metal at once. On thin stock, such as a steel stud or a strip of sheet metal, you want several teeth touching the material so no single tooth catches the edge and chatters. A higher count like 54 helps with that.

On thicker pieces, such as heavy angle iron or flat bar, each tooth has more metal to clear. Fewer, larger gaps between teeth give the chips room to leave the cut, so a count like 42 suits that work well.

Match teeth to the finish you want

More teeth generally leave a smoother edge with smaller burrs, which saves filing time on pieces that will show, like a railing or a shelf bracket. Fewer teeth tend to cut more aggressively and leave a rougher edge that may need a quick pass with a file.

The 48-40-4515 is designed to give clean cuts. [2] If you’re choosing between sizes for mixed jobs, picture your most common cut: thin conduit and studs point toward the higher count, and thicker structural steel points toward the lower one.

Close-up of a circular saw blade's carbide teeth biting into a piece of steel angle iron, with small metal chips flying.

Metal vs stainless: what the carbide is made of

Milwaukee sells its metal blades as the Metal & Stainless line, and the carbide teeth are what let one blade handle mild steel and tougher stainless. The 8 in 48-40-4515, for example, is listed as a Metal & Stainless Cutting Circular Saw Blade. [2] The 5-3/8 in 48-40-4070 carries the same Metal & Stainless name. [3]

Cobalt-infused tungsten carbide

The teeth are made of tungsten carbide infused with cobalt. [3] Tungsten carbide is a very hard material that holds an edge far longer than plain steel teeth. Cobalt is the binder that holds the carbide grains together, and it helps the tips stand up to the heat and impact of cutting metal.

In practice, this means you can run the same blade through a galvanized stud and then a stainless bracket without swapping blades. Carbide tips can chip if you force the saw or let the work bounce, so let the blade do the cutting at a steady feed.

Built for dry cutting

These blades are designed for dry metal cutting. [2] Dry cutting means you run the blade without coolant or cutting oil, so there’s no mess to clean up and no fluid on the floor of a job site or garage.

That also makes them a good match for cordless and corded metal-cutting circular saws, which have no coolant system. You cut, the chips fly out, and the piece is ready to handle once it cools.

What they cut

The line is made for ferrous materials, meaning metals that contain iron. Typical jobs include pipe, angle iron, steel studs and conduit. [4]

A few everyday examples:

  • Trimming steel studs to length for a basement partition wall

  • Cutting EMT conduit runs for a garage electrical project

  • Squaring off angle iron for a shelf bracket or trailer repair

  • Shortening threaded steel pipe for a plumbing or fence job

Cutting metal safely with a circular saw

Cutting metal with a circular saw throws hot chips and sparks, so protect your eyes, clamp the piece down and use a saw that is rated for metal. Those three habits prevent most of the injuries and ruined cuts people run into the first time they try it.

Gear up and secure the work

Wear safety glasses or a face shield every time, even for a single short cut. Steel chips come off the blade hot and fast, and they can bounce off the floor or a nearby wall toward you.

Clamp the workpiece to a sturdy bench or sawhorses with at least two clamps. A loose piece of angle iron or flat bar can shift mid-cut and pinch the blade. Keep the offcut side supported too, so it falls away cleanly instead of binding.

Clear the area of sawdust, rags and anything else that could catch a spark. A woodshop floor covered in shavings is a poor place to cut steel.

Use a saw built for metal

Put a metal cutting blade on a metal cutting saw, and leave your wood saw for wood. A metal cutting circular saw runs at a speed suited to carbide metal blades and usually has a guard that collects chips, which a typical wood saw lacks. If your saw’s label or manual does not say it handles metal, treat it as a wood-only tool.

Let the blade set the pace

Feed the saw steadily and let the teeth do the work. Forcing it overheats the blade and makes the saw kick or wander.

In 1/2 in steel, one user reported a cut rate of about 1 in per second. [5] That gives you a feel for normal speed: a 6 in wide plate takes roughly six seconds. If you are pushing much harder to go faster than that, ease off.

What these blades cost and whether they are worth it

Milwaukee metal blades cost more than basic abrasive or steel-tooth blades, and they are worth it when you cut enough metal to use up their longer life. Expect to pay anywhere from about fifty dollars to a few hundred, depending on size and where you buy.

What people actually pay

One welder who cuts steel with a Milwaukee blade paid $53 for it and called it “a bit expensive.” [5] That post dates from 2016, so treat it as a rough benchmark for a single blade from a few years back, not a current price.

A U.S. retailer lists the 5-3/8 in Metal & Stainless blade (48-40-4070) at $279.00. [3] That listing carries a 4.7 rating from 121 reviews, so buyers who paid it were largely satisfied. [3] A figure that high for a compact blade is worth a second look: read the listing to see whether it covers one blade or a pack, and check the current price on the retailer’s page before you order.

Judge the price by cost per cut

Milwaukee says it designs its metal blades for blade life, cut quality and speed in demanding metal cutting work. [6] Longer life is where the money comes back, so compare what each blade costs against how many cuts it gives you.

Here is a simple way to run the numbers for your own work:

  • Divide the blade price by the number of cuts you get before it dulls.

  • Add the time you lose swapping worn blades or cleaning up rough edges.

  • Compare that total with the cheaper blade you would otherwise buy.

If you cut a few lengths of conduit a year, a cheaper blade may cost you less overall. If you cut steel studs or angle iron every week, a blade that lasts longer and leaves cleaner edges usually pays for itself through fewer replacements and less grinding.

Questions people ask about Milwaukee metal blades

Can you cut aluminum with these blades?

These blades target steel and iron, so use a different blade for aluminum. Milwaukee aims its metal cutting circular saw blades at ferrous materials such as pipe, angle iron, steel studs and conduit [4]. Aluminum is a nonferrous metal: it is softer, melts at a lower temperature, and tends to gum up teeth designed for steel. To go further, see Saws for Cutting Steel Pipe and Metal Framing: Which to Choose.

If your project mixes metals, for example steel studs plus an aluminum threshold, plan on two blades. Read the package before you buy. A blade made for aluminum says “nonferrous” on the label, and that label is what you want for aluminum.

Can the blade go on a wood saw?

No. Put a metal cutting blade on a saw built for cutting metal. A Milwaukee metal blade such as the 8 in 48-40-4515 is sold in the Metal & Stainless Cutting line [2]. That line is meant to pair with a metal cutting circular saw.

A metal cutting saw usually has a guard and housing that collect chips, which a wood saw lacks. If you only own a wood circular saw and need to cut steel studs or conduit, add a metal cutting saw to your kit.

Wet or dry cutting?

Cut dry. Milwaukee describes these blades as ideal for dry metal cutting [2]. That means you don’t need coolant, a water feed or cutting oil.

In practice, you clamp the pipe or angle iron, line up your mark and make the cut with the blade running dry. Skipping coolant also keeps the work area cleaner. You won’t have oily residue on the steel when you paint or weld it afterward, and you won’t have water near a corded saw.

Picking your blade

Your blade choice comes down to two matches: the right diameter for your saw and the right tooth count for the metal you cut. Start with the saw, since its rated blade size is fixed. Milwaukee’s metal blades come in diameters from 5-3/8 in to 14 in, so there is a size for most saws, from compact cordless models to large ones [1].

Next, look at what you cut most often. Thin material like steel studs or conduit favors more teeth for a cleaner, smoother cut, while thicker stock such as angle iron works better with fewer, larger teeth. Read the blade size printed on your saw’s guard, then pick the tooth count that fits your typical job.

Sources

  1. Milwaukee – Circular Saw Blades

  2. Milwaukee 48-40-4515 8″ Metal Cutting Circular Saw Blade

  3. Milwaukee 5-3/8″ Metal & Stainless Cutting Circular Saw Blade – (48-40- …

  4. Milwaukee Saw Blades

  5. Milwaukee metal cutting circular saw blades | WeldingWeb Community

  6. Circular Saw Blades and Accessories