Pick your Milwaukee oscillating multi tool blades by what you are cutting and how the cut has to look. A wood blade, a bi-metal blade for nail-embedded wood, a grout blade and a scraper each do one kind of job well, and the wrong one dulls fast or leaves a rough edge.
If you remodel, patch drywall or trim door jambs now and then, a mixed blade kit covers the common jobs for most DIYers. If you do one job over and over, like undercutting jambs for new flooring, buying that one blade type in a multipack makes more sense.
Milwaukee sells multi-tools in both its M12 and M18 cordless lines, so the blade question is the same whichever battery platform you own. [1] Below, you’ll find which blade fits wood, metal, drywall and grout, how to confirm the mount fits your tool, and how to make each blade last.
What blade cuts wood and trim cleanly
For clean, fast cuts in wood and trim, pick a wood-cutting blade with coarse teeth for general work and a flush-cut blade when the cut has to sit level with a surface. Those two blades handle most trim and carpentry jobs a DIYer runs into. Keep them out of anything with metal in it.
Coarse teeth for fast cuts in softwood
Larger, widely spaced teeth remove wood quickly because each stroke clears more material. That makes a coarse wood blade the one to grab for pine, fir and other softwood framing or trim.
Typical jobs include notching a 2×4 to fit around a pipe, cutting an opening in a pine shelf or shortening a baseboard that is already nailed in place. The tradeoff is a slightly rougher edge, which matters less on hidden cuts and more on visible trim. On a face that shows, go slowly and plan a light sanding pass.
Flush-cut blades for jambs and dowels
A flush-cut blade lets you saw parallel to a surface and leave the cut level with it. The blade sits flat against the floor or wall while the teeth at its tip do the cutting.
The classic example is undercutting a door jamb so new flooring slides underneath. Lay a scrap of the flooring on the subfloor, rest the blade on top of it and cut through the jamb at that height. The same blade trims a dowel or plug flush with a tabletop, or cuts off a shim sticking out from behind a door frame.
Keep the blade flat and let the tool set the pace. Tipping it even slightly can gouge the surface you are trying to protect.
Why wood-only teeth dull on nails
Wood-cutting teeth are shaped for wood fibers, so a hidden nail or screw can blunt them quickly. One hit can leave a fresh blade burning and dragging instead of cutting.
Before cutting old trim or a door jamb, look for finish nail heads and filled holes. If you can’t be sure the wood is clean, use a blade made for nail-embedded wood and save your wood blade for clean stock.

Which blades handle metal and nail-embedded wood
For metal and wood that may hide nails, reach for a bi-metal blade, and switch to carbide when the material is hard or abrasive enough to wear bi-metal teeth down fast. Both blade types cost more than wood-only blades, but they keep cutting in situations where a wood blade would lose its teeth in seconds.
Bi-metal blades for demolition and repair
Bi-metal blades combine a flexible body with hardened teeth, so they can hit a nail or screw without stripping. That makes them the everyday blade for remodeling. Use one to cut a door jamb that still has finish nails in it, trim subfloor around a toilet flange, or cut through a baseboard without pulling the nails first.
If you buy only one blade beyond the wood blade, make it bi-metal. You give up a little speed in clean softwood, and in exchange you can cut almost any wood you find in an older house.
Fine teeth for sheet metal, pipe and bolts
Tooth count matters as much as tooth material when you cut metal. Fine, closely spaced teeth keep several teeth on thin material at once, so the blade cuts smoothly instead of grabbing and chattering. Here are jobs that call for a fine-tooth bi-metal blade:
Cutting a seized bolt or a rusted screw flush with the surface
Trimming copper or thin-wall pipe where a hacksaw won’t fit
Notching sheet metal, ductwork or metal flashing
Cutting a nail between two boards, such as a stuck window stop
Coarse teeth catch on thin metal edges. Keep them for wood.
Carbide when the cut is hard or abrasive
Carbide teeth hold an edge much longer than bi-metal in tough material. A carbide blade suits hardened screws, cast iron, fiber cement, and wood that is packed with nails or old fasteners. It costs more up front, but for a job like cutting out a long run of nailed flooring, one carbide blade can save you from stopping again and again to change dull bi-metal blades.
If you cut metal or nailed wood only now and then, bi-metal covers you. Carbide pays off when you make many abrasive cuts in a single project.

What to use for drywall, grout and tile
For drywall, grout and tile, match the blade’s edge to the material: drywall cuts cleanly with a standard wood-style blade, grout comes out with a toothless abrasive-edge blade, and scraper blades lift adhesive, caulk and old finishes. You don’t need a fine-tooth blade for any of these jobs.
Drywall
Drywall is soft, so a fine tooth adds nothing. A coarser wood-cutting blade plunges straight into the sheet and moves fast, which helps when you’re cutting an opening for an outlet box or a recessed light.
For a box cutout, mark the outline, plunge-cut each side and lift the piece out. The oscillating motion keeps the edges tidy enough for a cover plate to hide them. Save your bi-metal and carbide blades for harder work. Gypsum dust wears their edges without giving you a better cut.
Grout
Grout removal calls for a blade with no teeth at all. Its edge is coated with an abrasive grit that grinds the grout away. A toothed blade would catch, chatter and chip the tile edges.
These blades come in thin profiles for narrow joints and wider ones for wide joints. Pick the one that fits inside the joint without rubbing the tile faces. Guide the blade along the joint in steady passes, and let the grit do the cutting rather than pressing hard. That way you clear old grout before regrouting, or loosen a single cracked tile so you can replace it.
Adhesive, caulk and old finish
Scraper blades have a flat, wide edge in place of teeth. Rigid scrapers lift vinyl tile adhesive, mastic and peeling paint off a floor or wall. Flexible scrapers follow a surface more closely, which suits caulk along a tub or old sealant around a window.
Hold the scraper at a low angle and push it under the material, the way you would a putty knife. The vibration breaks the bond, so a strip of hardened caulk often comes away in long pieces.
Protect your eyes and lungs with grout
Cutting grout throws grit and fine dust, so wear safety glasses or goggles and a dust mask or respirator. Connect a shop vacuum near the cut if your tool has a dust attachment, and keep the room ventilated. The fine dust settles everywhere and is easy to breathe in when you’re working close to the floor or wall.
Will the blades fit your tool, and is a kit worth it
Before you buy any blade, match its mounting pattern to the arbor on your multi-tool. The mount is the shaped hole at the back of the blade that locks onto the tool. If the shapes don’t match, the blade either won’t seat or will sit loose and wobble, which ruins cuts and wears the tool.
Matching the mount
The blade package lists which mount it uses and which tools it fits. Compare that with the mount named in your tool’s manual or printed on the tool’s packaging. Check this even if you own a Milwaukee tool and are buying Milwaukee blades, because blade lines and tool generations can differ.
A quick test settles it: set the new blade against the arbor before you tighten anything. It should drop onto the locating pins with no gap and no rocking. If you have to force it, stop and return it.
When a kit makes sense
A kit pays off when your project list is mixed. A bathroom remodel is a good example: you may trim a door jamb on Monday, cut out drywall for a new outlet on Tuesday, and dig out grout on Friday. A kit puts a wood blade, a bi-metal blade and often a scraper or grout blade in one box, so you aren’t driving to the store mid-job.
The tradeoff is that some blades in a kit may sit unused for years. If you can’t name at least a few jobs you’d use the extra blades for, a kit is less of a bargain than it looks.
When single blades are smarter
Buy single blades, or multi-packs of one blade, when you’re doing the same cut over and over. Flooring is the classic case: undercutting door casings for new plank or tile floors uses one flush-cut blade again and again. Buying several of that blade keeps you working when the first one dulls, and you skip paying for blades you won’t touch.
Blade and kit prices shift often between retailers and sales, so check the current price on the retailer’s page and compare the per-blade cost of a kit against buying singles.
How to make blades last longer
Blades last longest when you let the motor and the oscillating motion do the cutting while you guide the tool lightly. Most dull or burned blades come from leaning on the tool, from cutting in a slot packed with dust, or from wearing out one small patch of teeth while the rest stay sharp.
Let the speed do the work
Set the speed to suit the material and the cut, then feed the blade in with light, steady pressure. If you push hard, the teeth stall against the wood or metal. They rub instead of cutting, and that heats them and dulls them fast. A good cue is the sound: a steady buzz means the blade is cutting, and a bogging, laboring tone means you are pushing too hard.
For example, when you plunge into a subfloor to cut out a damaged section, start the cut slowly and let the teeth bite before you add depth. If progress stalls, ease off. More pressure is not the fix.
Rock the blade to clear dust
An oscillating blade moves only a few degrees side to side, so sawdust and grit pack into the kerf quickly. A packed kerf traps heat against the teeth and slows the cut. While you cut, rock the tool gently back and forth a little so the dust can clear out of the slot.
This matters most in deep plunge cuts, such as cutting an opening in a wall or trimming a door jamb for new flooring. If you see smoke or dark burn marks, pull the blade out partway, let the chips fall clear, and continue.
Spread wear across the edge
Most people cut with the same spot on the blade every time, usually the corner or the center. That spot dulls while the rest of the edge stays sharp. Shift where the blade contacts the work so the whole edge does its share.
Most blades fit the tool’s mount in several positions. Loosen the blade, rotate it to a new angle, and reattach it. That brings a fresh section of teeth into use. On wide blades, you can also start some cuts with the left side and others with the right. Changing the angle or the starting point this way can stretch one blade across a much bigger job, such as undercutting all the door jambs in a room.
Your next step
Match the blade to the material and you’ll get cleaner cuts with less effort. For most remodeling work, start with two blades: a bi-metal blade for wood that may hide nails or screws, and a flush-cut wood blade for trimming door jambs, casing and dowels level with the floor or wall. Together they handle most of what a typical room update throws at you.
If your project includes tile, add a grout blade before you start so you aren’t stuck mid-job. Once any blade stops cutting smoothly, swap it for a fresh one. Pushing harder on a dull blade slows the cut, heats the tool and leaves a rougher edge, while a new blade cuts cleanly again right away.