The DeWalt FlexVolt 120V sliding miter saw is worth it if you cut on jobsites or in rooms without a handy outlet, because the DHS790 runs either corded or on batteries. Corded use gives you unlimited runtime, and battery use lets you set up where there’s no power. [1] The catch is weight: this is a big 12-inch slider you’ll want to carry as little as possible. Related reading: RIDGID 18V Brushless Sliding Miter Saw vs. Bosch GCM18V-08N.
DeWalt makes this saw as a sliding model (DHS790) and a non-sliding model (DHS716), and this review is about the slider. [2] It has belt-driven power and fits carpenters and remodelers who move between rooms and job sites. [3] It makes less sense for a fixed shop bench with an outlet nearby. Below you’ll find how the power setup works, how much it can cut, how heavy it is to move, and who should skip it.
How does the corded or battery setup work
You can run this saw two ways: plugged into a wall outlet or on batteries. The FlexVolt 12 in. 120V MAX sliding miter saw is corded for unlimited runtime or cordless for portability, so the choice comes down to where you’re cutting and for how long. [1]
Cordless mode for moving around a site
On batteries, the saw goes wherever you can set it down. Cordless operation is built for portability. [1] That helps on a new build before the power is hooked up, on a deck out in the backyard, or in an upstairs room where the nearest outlet is two floors away.
You also skip the extension cord. You won’t have a cord running across a walkway for someone to trip on, and you won’t be hunting for a free outlet that isn’t already feeding a compressor or shop vac.
Corded mode for long cutting sessions
Plugged in, the saw keeps cutting for as long as you have work. Corded mode gives unlimited runtime. [1] Use it when you’re cutting a full room of baseboard, a stack of deck boards or a day’s worth of framing, where you’d otherwise be swapping and recharging packs.
Corded mode also suits a garage or shop with a reliable outlet near the bench. When power is right there, you have no reason to spend battery charge.
What comes in the box
The saw is sold as a 2-battery kit. [1] With two packs you can run on one while the other charges, which makes cordless work more practical over a longer day.
Picking the right mode for the job
Think about job length and outlet access before you set up:
Short jobs with no power nearby, such as trimming a few rafters or cutting trim in a finished room, are a good fit for batteries.
Long jobs with an outlet close by, such as cutting all the flooring transitions for a house, are a good fit for the cord.
On jobs where power shows up partway through, start on batteries and switch to the cord once outlets are live.
A simple rule: go cordless when you’d otherwise need a long extension cord, and plug in when you’ll be cutting for hours from one spot.
How much cutting power does it have
The DHS790 has enough motor for full-size jobsite work: its 15 amp motor spins a 12-inch blade at 3800 RPM. [4] That figure is the no-load blade speed. In practice it means the saw keeps enough speed for the hardwood trim, framing lumber and plywood a remodeler cuts on a typical job.
What the 15 amp, 3800 RPM numbers mean
Amps tell you how much current the motor can draw. A 15 amp motor is the standard size for full-power corded miter saws, so this saw sits in the same class as the bench saws you see on most sites. RPM is how fast the blade turns before it touches the wood. A faster blade leaves a cleaner cut and is less likely to stall when you push through dense stock.
The practical test is a hard cut. On a 2×10 of Douglas fir or a piece of 5/4 oak, a saw with this much motor should cut steadily without bogging down, as long as your blade is sharp and you feed at an even pace.
Why the belt drive matters
Reviewers describe the DHS790 as delivering powerful belt-driven performance. [3] On a belt-driven saw, a belt carries power from the motor to the blade arbor, and the motor does not mount directly on the blade shaft. Belt drives tend to run quieter, and the belt can take up some of the shock when the blade hits a knot.
The drawback is upkeep. A belt can stretch or wear over years of use and may eventually need replacing. Plan for that if you keep a saw for a long time.
What a 12-inch blade does for wide and thick stock
A bigger blade reaches farther into the work. Compared with a 10-inch saw, a 12-inch blade cuts deeper, which helps with thick posts, stacked boards and tall baseboard stood on edge against the fence. The sliding arm then carries that blade across wider boards, so you can crosscut shelving or stair treads in one pass.
The trade-off is blade cost and size. Twelve-inch blades cost more to replace, and the larger blade adds bulk to the saw head. If most of your cuts are 1×4 trim, you are paying for capacity you won’t often use.

How heavy is it to move around
The DeWalt FlexVolt 120V sliding miter saw weighs approximately 56 pounds, so you can carry it, but you won’t want to carry it far or often. [4] That’s about the weight of a big bag of concrete mix, and it comes in an awkward shape with a long fence, a sliding rail system and a 12-inch blade guard sticking out.
Short moves are fine
Most people can manage a one-time trip from the truck bed to the room where they’ll work. You lift it once in the morning, set it up and leave it there for the day.
A few habits make that trip easier:
Lock the slide rails and the miter table before you lift, so the head doesn’t shift and throw off your balance.
Lock the head down in its lowest position to shrink the profile and keep the blade guard closed.
Carry it close to your body with both hands, and clear a path through doorways before you pick it up.
Ask for a hand on stairs, where a 56-pound saw gets heavy fast.
Frequent carrying gets old
If your work means moving the saw between rooms several times a day, or up and down stairs on every job, the weight adds up. A remodeler cutting trim in three rooms of a house will feel it by the afternoon.
This is where cordless mode helps a little: with no cord to manage, you can move the saw closer to the work instead of running stock back and forth. It doesn’t make the saw any lighter, though.
Plan for a stand or cart
Budget for a miter saw stand from the start. A stand with wheels lets you roll the saw from the truck to the job instead of carrying it, and it puts the table at a comfortable cutting height so you aren’t working on the floor or a pair of sawhorses.
Look for a stand with outfeed supports on both sides. A 12-inch slider is often used for long trim and wide boards, and the supports keep that stock level so cuts stay square. In a garage, a rolling cart or a dedicated bench does the same job, and once the saw is mounted you rarely have to lift it at all.
Sliding DHS790 or non-sliding DHS716
Pick the DHS790 if you need to crosscut wide boards, and the DHS716 if bench space matters more than cut width. The FlexVolt 12-inch saw comes in two models: the DHS790 is a double bevel compound sliding miter saw, and the DHS716 is a double bevel compound non-slider [2]. Beyond the slide, the two share the same basic design [2].
What the slide changes
A sliding saw mounts the motor and blade on rails, so you pull the head toward you, push it down, and then push it back through the board. The blade travels across the wood, which lets it cut boards wider than a fixed blade can reach in one plunge. A non-slider only chops straight down, so its cut width stops at what the blade covers in that single motion.
For example, if you’re crosscutting wide shelving stock or stair treads, the slide lets you finish each cut in one pass. With a chop-only saw, you’d flip the board and cut from the other side, or switch to a circular saw.
What both models share
Both saws are double bevel compound [2]. Double bevel means the head tilts both left and right, so you can cut a bevel in either direction without flipping your workpiece end for end. That helps a lot on long trim and crown, where flipping a 10-foot board is awkward.
Compound means you can set a miter angle and a bevel angle at the same time for cuts like crown molding corners. DeWalt lists the FlexVolt cordless double bevel sliding compound miter saw in its current miter saw lineup [5].
Feature | DHS790 | DHS716 |
|---|---|---|
Cutting action | Sliding | Non-sliding (chop) |
Bevel | Double bevel | Double bevel |
Compound cuts | Yes | Yes |
Footprint | Needs room behind for rails | More compact |
The slide is the only real difference between the two. Choose the DHS790 when wide crosscuts come up often, since the rails extend your reach across the board. Choose the DHS716 when you mostly cut trim and narrower stock and want a saw that sits closer to the wall or fits a tighter truck bed.
Who should buy it and who should skip it
This saw makes the most sense if you cut trim, framing or flooring in places where an outlet is far away, still in the works, or shut off. It was built with carpenters and remodelers in mind, and its belt-driven performance is aimed at that kind of work [3]. If your cuts happen at a garage bench a few feet from a wall plug, you may be paying for a battery option you will rarely use.
Good fit: carpenters and remodelers on the move
Picture a kitchen gut where the electrician has the panel off, or a deck job at a new build with no temporary power yet. You can run the saw cordless in those places and keep working without waiting on a generator or stringing extension cords through the house [1]. The same saw plugs in once power is back, so you are not stuck with two machines for two situations [1].
It also helps on small punch-list jobs. If you only need to cut a few pieces of baseboard in a finished room, you can leave the cord in the truck and keep a trip hazard off the client’s floor.
Maybe skip it: garage and shop users near an outlet
When your saw lives on a stand in the garage and the outlet is always within reach, the battery feature has little to offer. You would run it corded nearly every time. Your money can go further on a corded 12-inch slider, a better blade or a solid stand.
This also holds if you take on only a project or two each year. Batteries that sit unused for months give you less value than a saw that just plugs in.
A plus if you already own FlexVolt batteries
If your drill, circular saw or grinder already runs on FlexVolt packs, this saw fits into a system you have already paid for. You can swap packs between tools, keep spares charged and carry a single charger type to the job. The math is less appealing if you are on another battery platform and would be starting FlexVolt from scratch.
If your work is mostly smaller trim and you care more about a lighter cordless saw, the 10-inch cordless options are a separate comparison worth reading.
Next step before you buy
Buy the FlexVolt 120V slider if you need 12-inch sliding capacity in places where an outlet is far away or missing. If you mostly cut in a garage next to a wall plug, a corded 12-inch slider will do the same work for less money and without batteries to charge.
Your next step is the retailer page. The saw is sold as a 2-battery kit, so look at exactly which batteries and charger come in the box and what the current price is before you commit [1]. Then put it side by side with the other 12-inch sliders in our roundup of the best 12-inch sliding miter saws. Compare weight, footprint and price against how often you will actually run it cordless.
