The Porter Cable PC560 Quik Jig is a bench-top pocket hole system that works with the standard power drill you already own to make precise pocket holes. [1] It sits on your bench instead of clamping to the board in your hand, so it fits a shop setup better than quick fixes on site.
The jig is built mostly of aluminum, with steel and ABS plastic accessories. [2] That makes it a sturdy, durable bench tool, a good match if you want a solid jig that stays put. [3] If you’d rather carry a small handheld jig from job to job, a lighter option may suit you better.
Below you’ll see how the PC560 makes pocket holes and what comes in the box. You’ll also learn what it costs new or used, and which projects it handles best.
How does the Quik Jig make pocket holes?
The Quik Jig drills a steep, angled hole in one board so a screw can pull it tight against a second board. You supply the drill, and the jig holds the bit at the right angle so every hole lands where it should.
Pocket hole joinery in plain words
A pocket hole is a hole drilled at a shallow angle into the face of a board, coming out near its edge. You drive a screw through that hole and into the neighboring board, and the screw head sits down inside the pocket. The two boards clamp together with no dowels or biscuits to line up.
Picture joining a face frame for a cabinet. You drill two pocket holes into the end of a rail, butt it against the stile, and drive the screws. The joint is done in a couple of minutes, and the holes sit on the back where nobody sees them. Pocket hole joinery is a very popular way to build. [4]
Your drill does the cutting, the jig does the aiming
The PC560 has no motor. You chuck the pocket hole bit into your standard power drill, and the jig’s guide keeps that bit at a fixed angle and position as you drill. That guidance is what lets the system make precise pocket holes. [1]
This matters because the hard part of a pocket hole is the angle. Drilling one freehand would leave you with holes that wander, screws that poke through the face, or joints that pull out of line. With a guide, the bit enters the same way every time, so you can focus on feeding the drill smoothly.
Why the bench-top design helps
The PC560 is a bench-top tool. [3] It sits on your workbench, and you bring the board to it, clamp it, drill, and move to the next piece. Because the jig stays put, the board is held steady while the bit spins.
That fixed setup also makes your work repeatable. If you are building a set of drawer boxes and need 24 identical holes, each board goes into the same spot and comes out drilled the same way. The maker describes the system as built to make woodworking jobs more efficient and accurate. [3]
What comes in the box
The PC560 kit gives you the parts that turn your own drill into a pocket hole tool: a pocket hole drill bit with a depth stop, two square drive bits of different lengths, and a place on the jig to store all of it. [5] You supply the drill and the screws.
The pocket hole drill bit and depth stop
The drill bit is the part that cuts the angled hole. It is a stepped bit, so one pass bores a wider pocket for the screw head and a narrower pilot hole for the screw shank. The depth stop is a collar that clamps onto the bit. It controls how far the bit goes into the jig, which sets how deep the pocket is. [5]
Set the stop for the thickness of the board you are drilling. For example, if you move from 3/4-inch face frame stock to a thinner panel, reset the collar first. Otherwise the screw tip can break through the face of the second board.
Two square drive bits
The kit has two square drive bits, and they are different lengths. [5] Square drive, also called Robertson drive, grips the screw head more firmly than a Phillips bit. It is less likely to slip out of the screw (cam out) when you drive a screw at an angle down a narrow pocket.
The two lengths cover different reach needs:
The shorter bit is easier to control for most open joints at the bench.
The longer bit reaches screws at the bottom of deep pockets or inside a cabinet box, where the drill body would otherwise hit the work.
Onboard storage
The jig has built-in storage for the drill bit, the depth stop and the two drivers. [5] Everything stays on the jig itself, so you are not digging through a drawer for the right bit halfway through a glue-up.
This matters most in a shared or busy shop. A small depth stop collar is easy to lose, and the jig is much less useful without it. Putting each part back in its slot after a session keeps the kit complete and ready for the next project.
Build quality and warranty
The PC560 is built to last on a workbench, and that is a big part of why it cost more than basic jigs. Its main body is aluminum, which keeps it rigid without making it a chore to move around the shop.
Materials and what they mean for you
The jig is built primarily of aluminum with steel and ABS plastic accessories. [2] In practice, that mix puts each material where it does the most good:
Aluminum forms the body, so the base stays flat and won’t rust if your shop gets damp.
Steel handles the parts that take wear, such as the drill bit, where softer metal would wear down.
ABS plastic covers lighter-duty pieces that don’t carry clamping or drilling loads.
ABS is a tough, impact-resistant plastic common in power tool housings. Even so, plastic parts are the first place to look for cracks or worn edges on a jig that has seen years of use. A chipped plastic piece rarely stops the jig from working, but it can make setup less smooth.
Warranty coverage at launch
When Porter-Cable released the QUIKJIG (model 560), it came with a three-year limited warranty and one year of free service. [6] For a new buyer back then, that meant three years of protection against defects, plus a year in which Porter-Cable would handle service.
A limited warranty usually covers defects in materials and workmanship, not wear from normal use or damage from misuse. If a bit dulls after a few hundred pocket holes, that is wear. If the aluminum body arrived warped, that is a defect.
Buying used? Plan as if there is no warranty
The PC560 has been on the market for years, so most units you’ll find today are well past a three-year window. Treat any used unit as uncovered unless the seller has an original receipt and Porter-Cable confirms the coverage applies to you.
That changes how you judge a used price. Without warranty backing, any repair or replacement part comes out of your pocket, so a solid, complete unit is worth more than a cheap one with visible damage. Check that the aluminum base sits flat on your bench and that nothing wobbles before you hand over cash.
What does it cost, new or used?
That price is the cost of a bench-top system. If you only build a bookshelf or two a year, a simpler jig may cover you for less money.
Buying new versus used
The used market is the usual place to find a PC560 now. Woodworking forums carry for-sale posts for the jig, including one from March 2024 [5]. eBay lists it with both new and used options [7]. A used kit can save you a good share of the original price, but only when every part is in the box.
Where you buy affects how much you can learn before you pay:
Forum sellers are often woodworkers who can tell you how much the jig was used and send extra photos on request.
Marketplace listings make it easy to compare several kits, though the photos and descriptions vary a lot.
Local pickup lets you handle the jig and open the storage compartments yourself.
What a complete used kit includes
A complete kit has a pocket hole drill bit with its depth stop and two square drive bits of different lengths [5]. The jig has onboard storage for all of these parts [5]. That makes a quick look easy: open the storage spots and see what is missing.
The drill bit and depth stop matter most. The bit is a stepped bit made for pocket holes, and the depth stop sets how deep it cuts, so without them the jig cannot drill a proper hole. Missing drivers matter less, but two square drive bits in the lengths you need still add cost and a trip to the store.
If a listing photo shows empty storage slots, ask the seller about it. Then subtract the price of the replacement parts from your offer. A worn or chipped drill bit counts as a missing one, because you will replace it before your first project.
Is the PC560 the right jig for your projects?
The PC560 pays off when you build the same joint again and again at a workbench, such as cabinet boxes, face frames or a run of drawer carcasses. It is a bench-top system built to be sturdy and durable, and the maker pitches it as a way to make woodworking jobs more efficient and accurate. [3] In practice, that means you clamp board after board in the same spot and get matching holes without resetting anything.
Where it fits best
Think about a kitchen or shop cabinet project. A single face frame for a 36-inch base cabinet can need a dozen or more pocket holes across the stiles and rails, and a full set of cabinets multiplies that fast. A jig that stays put on the bench lets you work through a stack of rails in one session while every hole lands at the same depth and spacing.
The PC560 also suits you if you have a dedicated shop space. Projects that tend to work well with it include:
Face frames for cabinets, bookcases and built-ins
Cabinet boxes and carcasses assembled from plywood panels
Batches of identical parts, like shelf supports or frame-and-panel pieces
Furniture where you want each joint to match the last one
When it may be more than you need
If you only drill pocket holes a few times a year, the PC560 can be hard to justify. It was not a cheap jig when reviewed, so the cost per project is high if it spends most of its time on a shelf. [2] A one-time fix, like screwing a loose stool rail back together, rarely calls for a bench system.
Space is the other factor. A bench-top jig needs room on your workbench while you use it and a spot to store it afterward, which matters in a garage you share with a car. It also stays in the shop, so it is less handy for repairs on a deck or at a job site.
If portability or occasional use sounds more like you, the Kreg 520PRO review covers the handheld alternative.
Making your choice
Choose the PC560 Quik Jig if you do most of your pocket hole work at a bench and want a jig that stays put and repeats the same hole every time. Its aluminum body with steel and ABS plastic parts is built for that kind of steady shop use [2].
If you’re buying a used kit, open the onboard storage before you pay. It should hold the pocket hole drill bit, the depth stop and two square drive bits of different lengths [5]. If portability matters more than a solid bench setup, for example when you build on site or move between rooms, compare it against a handheld jig like the Kreg 520PRO before deciding.
